manualshive.com logo in svg

aculab E1, Руководство по установке, Страница: 28 / 31

Поделиться
Скачать
aculab E1 Скачать руководство пользователя страница 28

E1/T1 PCI card installation guide 

28 

Appendix E: Technical Specifications 

Connectors 

• 

PM 4, 2 or 1 modules–8 way RJ45/RJ48 balanced (120R/100R) 

Line interface 

• 

E1 2Mbit to G703/G704/I431 

• 

Doubleframe, CRC4 multiframe and CAS multiframe supported 

• HDB3 

line 

encoding 

• 

T1 1.544Mb to G703/G704/ANSI T1.403 

• 

D4 and ESF support 

• 

AMI or B8ZS line encoding 

TDM interfaces 

• 

H.100 compliant interface supporting connection to any of the 4096 timeslots 

Switching 

• 

256 full duplex channel switching between the local resources and the H.100 bus 

• 

PM4 - Quad trunk 120/96 or 92 channels between network and TDM interface (E1, T1 or 
T1 PRI) 

• 

PM2 - Dual trunk 60/48 or 46 channels between network and TDM interface  
(El, T1 or Tl PRI) 

• 

PM1 - Single trunk 30/24 or 23 channels between network and TDM interface  
(El, T1 or Tl PRI) 

• 

Local switching of 120 channels to optional signalling DSP modules 

Clocking 

• CT 

bus 

slave 

 

• 

CT bus master supporting clock fallback 

Embedded processors 

• 

AM188 @ 20MHz - One per network port 

Signalling DSP modules (DSP32) 

• 

MF/DTMF tone signalling support. Conferencing, A-law/

µ

-law conversion, Attenuation, Fax 

and Bit Error rate testing 

• 

1 or 2 DSP32 modules providing up to 2 DSPs per network port 

Power supply (+5V DC +/- 5%) 

• 

Pre revision 1.4 PCI card with standard PM4   

 

17W 

• 

Revision 1.5 and later PCI card with standard PM4 

 

12W 

• 

Plus for each DSP32 module fitted (maximum 2) 

 

 4W 

Physical dimensions 

• 

All Aculab PCI products conform to PCI local bus specification revision 2.1 

• 

Overall dimensions (excluding face plate): 

 

Height 106.68mm +/- 0.127mm 
Depth (including retainer) 340.74mm +/- 1.57mm 
Depth (excluding retainer) 312mm +/- 0.127mm 
Each PCI card fits into a single card slot without impinging any adjacent slots 

 

• 

For further details on PCI standards, please contact the PCI Special Interest Group at 
http://www.pcisig.com/home. 

 

Содержание E1
































Отзывы:

Нет отзывов