manualshive.com logo in svg

ActronAir CL01-2G, Руководство по эксплуатации

Поделиться
Скачать
ActronAir CL01-2G Скачать руководство пользователя страница 27

Operation Manual

CL01-2  Wall Controller

Operation Manual - CL01-2 Wall Controller

Document: 0525-081  

 Ver. 1 190903

 

27

16. Troubleshooting Guide

Condition

Causes or Check Points

The system does not start

Check that 5 minutes has passed from Turn-On time, as the system has in built timers.
Check that setpoint temperature settings are correct.
Check that the setpoint temperature is set low enough for cooling or high enough for 
heating.

Air does not flow

(Indoor Unit)

During heating operation, air does not flow out for approximately 15 seconds after start 
up, this prevents cold draft.
Check for Auto Fan operation.

Cooling/Heating is not 

sufficient

The cooling/heating function may not work effectively when the indoor return air filter is 
clogged with dust and dirt.
Make sure the air inlet and air outlet on the outdoor unit are not blocked.
The outside temperature is above or below the design conditions.

Steam is coming out from the 

outdoor unit

It is caused by the defrosting of the outdoor unit in heating operation during cold ambient 
conditions. This is not a fault.

Water from the outdoor unit

This is normal during heating operation, which is due to water forming and running off the 
outdoor coil during defrost. This normal and it is not a fault.

Occurring of noises

When heating or cooling is started or stopped, a swishing or gurgling noise may be heard, 
This noise is generated by the refrigerant flowing between the outdoor and the indoor 
units.
A swooshing noise may be heard from the outdoor unit during operation. This noise is 
generated when the refrigerant changes direction in the defrost operation. 
On start up, the outdoor unit may be louder than normal for a few seconds while the 
compressor reaches the designated speed and operating pressure.
During defrost operation, the compressor may generate more noise than normal.

Setpoint temperature cannot 

be adjusted

The Control Interface has in built upper and lower limit setting. Setpoint temperature can 
only be adjusted within these limits. 

7-Day Time Clock is not turning 

the air conditioner On and Off

Check that the time clock events are set correctly.
Check that correct current day and time are set for the air conditioner to operate. 

BEFORE CONTACTING YOUR INSTALLER, PLEASE HAVE YOUR AIR CONDITIONERS

 MODEL NO. AND SERIAL NO. WITH YOU. (SEE PAGE 5)

Содержание CL01-2G































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды