ACR Electronics : 2846.0 Скачать руководство пользователя | Manualshive

Страница: 31 / 44

background image

Y1-03-0233 Rev. L

30

APPENDIX C - USER INTERFACE: DIGITAL DISPLAY
DURING OPERATION

The following chart describes the audio-visual feedback the beacon provides during
activation. The messages on the digital display typically appear as one or two words at a
time, until the entire message has been displayed.

GlobalFix™ iPRO Display, LED/ Audio Signaling and Description of Operation

The beacon has been activated and the ACR Electronics Welcome Page appears

Next, the product name appears

The system reports that the beacon is on and in activation mode

The system reports that the beacon has turned on the GPS engine

The system reminds you that for optimum GPS performance, i.e., greatest likelihood of
acquiring coordinates, position the beacon so that it has a clear view of the sky.

The system reminds you that for optimum transmission of the emergency message,
allow the beacon to float and do not hold the antenna (aerial).

The system reports that the 406 MHz emergency message has been sent. If this
message accompanied by a green LED flash, the GPS coordinates have been sent as
well. If accompanied by a red LED flash, the GPS coordinates have not been sent.

NOTE:

If GPS coordinates were not sent, the system will continue to attempt to

acquire the data and add it to the 406 MHz distress signal when available. Updated
GPS coordinates are sent every twenty minutes.

This message appears only if GPS data was acquired

GPS

SENT

DO

NOT

HOLD

AERIAL

GIVE

CLEAR

VIEW

TO

SKY

EPIRB

ON

GPS

ON

G

long beep

R

R

beep

406

SENT

R

G

«
...
29
30
31
32
33
...
»

Содержание : 2846.0













































Отзывы:

Нет отзывов

Похожие инструкции для : 2846.0

Бренд: Plastimo Страницы: 7

Бренд: West Marine Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды