ACR Electronics : 2846.0 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

ACR Electronics : 2846.0 Скачать руководство пользователя страница 25

Y1-03-0233 Rev. L

24

To remove the expired HRU

When opening the SeaShelter

3

™ lid, note that the beacon is installed

with  the  lanyard  face  in.  Pull  the  beacon  with  steady  pressure  from  the
bracket.  Do  not  get  beacon  wet  while  out  of  bracket.  The  HRU  has  a
keying feature that locks it to the bracket. If you view the HRU rod as the
center  of  a  clock,  a  properly  installed  HRU  will

rest at the 7 o’clock

position, as shown in the picture above.

WARNING:

The HRU holds down an ejection spring. The spring

must be held in place during the removal and installation of the
HydroFix™ to prevent injury.

Depress the top of the ejection spring. This will relieve pressure on the
HRU and allow it to be rotated counter

clockwise to the 5 o’clock position.

The HRU is now free to be removed. Slowly relieve pressure from the
ejection spring and allow it to deploy.

WARNING:

Discard the expired HRU. Failure to replace the entire

assembly may cause the bracket to malfunction.

WARNING:

Be sure to use only ACR’s HydroFix™ HRU (ACR P/N

9490) in the SeaShelter

3

™. Use of unauthorized replacement parts will

void your warranty and may cause the bracket to malfunction.

Check the date of manufacture on the new HRU. Follow the instructions
that accompany the HydroFix™ for marking the next expiry date and for
selecting the correct rod adapter for the SeaShelter

3

™.

To install the new HRU

Apply pressure to the ejection spring and hold it flat against the bracket.
With your free hand place the new HRU into the key way in the 5 o’clock
position and rotate clockwise to the 7 o’clock position. Slowly remove
pressure from the ejection spring. The HRU should now be held in the 7
o’clock position with the pressure on the ejection spring.

Reinstall the beacon with lanyard face in. Beacon should fit snugly in the
bracket  with  the  antenna  captured  by  the  bracket.  Reinstall  the  lid  by
seating  the  bottom  of the  lid  to the  detent  on  the  base. Close  the  upper
portion  of  the  lid  so  the  HRU  rod  lines  up  with  the  spring  loaded  knob.
With  gentle  pressure,  hold  the  lid  while  you  turn  the  lock
counterclockwise  until  it  stops,  then  clockwise  until  it  stops.  This  should
capture the HRU and snap the lid into a locked position. Confirm that the
lid is attached to the bottom of the bracket and the HRU.

CAUTION:

Do not force the lid closed. If the lid does not close

easily, check to see that the beacon is properly installed in the bracket
and the HydroFix™ is properly seated.

«
...
23
24
25
26
27
...
»

Содержание : 2846.0













































Отзывы:

Нет отзывов