ACME NEBULA Скачать руководство пользователя | Manualshive

Страница: 6 / 20

background image

5

D

4/5. FMX input /output:

DMX 512 link, use 5 XLR cable to link the unit and DMX controller.

6. Power In:

To connect to the mains supply

7. Power Out:

To connect to the next lamp supply

4. How to set the fixture

4.1 Menu

To select any of the given functions, press the

MENU

button up to when the required one is

showing on the display. Select the function by the

ENTER

button and the display will blink. Use the

DOWN

and

UP

button to change the mode. Once the required mode has been selected, press the

ENTER

button to setup, to go back to the functions without any change press the

MENU

button

again. Hold and press the

MENU

button about one second or wait for one minute to exit the menu

mode.

The main functions are showing below:

«
...
4
5
6
7
8
...
»

Содержание NEBULA





















Отзывы:

Нет отзывов

Похожие инструкции для NEBULA

Бренд: Panasonic Страницы: 78

Surge-Trap STP Series

Бренд: Mersen Страницы: 2

Бренд: Gobachi Страницы: 34

Бренд: Grandview Страницы: 4

Бренд: InFocus Страницы: 56

Бренд: Eiki Страницы: 81

Бренд: ViewSonic Страницы: 2

Бренд: Panasonic Страницы: 219

Бренд: Panasonic Страницы: 248

Бренд: Panasonic Страницы: 262

Бренд: Panasonic Страницы: 285

Бренд: Panasonic Страницы: 291

Бренд: Panasonic Страницы: 313

Бренд: Panasonic Страницы: 219

Бренд: Samsung Страницы: 40

The Premiere LSP7TFAXXE

Бренд: Samsung Страницы: 56

Бренд: Hitachi Страницы: 65

Бренд: Hitachi Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды