background image

8

D

 

Press the 

MENU

 button back to the last menu or let the unit idle one minute to exit menu mode. 

P/T Feedback 

To select 

P/T Feedback

, press the 

ENTER

 button to show the 

P/T Feedback

 on the display. 

Use the 

UP/DOWN

 button to select 

No 

(normal) or 

Yes

 (tilt inverse), press the 

ENTER

 button to 

setup. Press the 

MENU

 button back to the last menu or let the unit idle one minute to exit menu 

mode. 

BL.O. P/T Move 

To select 

BL.O. P/T Move

, press the 

ENTER

 button to show the 

BLACKOUT WHILE PAN/TILT 

MOVING

 on the display, use the 

UP/DOWN

 button to select 

No

 (normal while pan/tilt moving) or 

Yes

 (blackout while pan/tilt moving), press the

 ENTER

 button to setup. Press the 

MENU 

button 

back to the last menu or let the unit idle one minute to exit menu mode. 

Dimmer Curve 

To select 

Dimmer Curve

, press the 

ENTER

 button to show the 

DIMMER CURVE

 on the display, 

use the 

UP/DOWN

 button to select 

Linear

Square Law

Inverse Squ.

 or 

S-curve

. Once selected, 

press the 

ENTER

 button to store. Press the 

MENU

 button back to the last menu or let the unit idle 

one minute to exit menu mode. 

Linear: 

The increase in light intensity appears to be linear as DMX value is increased. 

Square Law: 

Light intensity control is finer at low levels and coarser at high levels. 

Inverse Square Law: 

Light intensity control is coarser at low levels and finger at high levels. 

S-cure:

 Light intensity control is finger at low levels and high levels and coarser at medium levels. 

Dimmer Speed 

To select 

Dimmer Speed

, press the 

ENTER 

button to show the 

DIMMER SPEED

 on the display. 

Use the 

UP/DOWN

 button to select 

Fast

 or 

Smooth

. Once selected, press the 

ENTER

 button to 

Содержание NEBULA





















Отзывы: