manualshive.com logo in svg

ACKERMANN 16-2050, Руководство пользователя

Поделиться
Скачать
ACKERMANN 16-2050 Скачать руководство пользователя страница 10

SHAVER SYSTEM

  

   

Ackermann

Page: 10 // 28

• connect the power cord provided with the device to the socket (16) on the back of the Control Unit,
• plug the power cord into the power socket. The voltage should be within the range indicated on the device label.

Turn on the device:
• A properly installed and connected device should be started using the “ON/OFF” switch (15) located on the rear panel.

The “STANDBY” button (5) will start flashing at a frequency of 0,5Hz, indicating that the device has switched to standby 

mode.

4.2. BASIC SETTINGS

• Once the device is in standby mode (see chapter 4.1.), press simultaneously and hold down the “SPEED DOWN” (8) and 
“SPEED UP” (9) buttons with your right hand.
• Still holding buttons (8) and (9) briefly press the “STANDBY” button (5) with your left hand.

• Once you are in the required menu, you can release these buttons. You can now select the language you require. The last 

selected language is shown.

To  change  the  language,  press  buttons  “SPEED  DOWN”  (8)  or  “SPEED  UP”  (9).  The  user  can  choose  between  German, 
English, French, Russian, Polish and Turkish. The selected language must be confirmed by pressing the button “TOOL” (10).

• Once the selected language has been confirmed, the next settings can be selected: oscillation time and brightness of the 
VDF display. Again, the settings are selected by pressing the buttons “SPEED DOWN” (8) or “SPEED UP” (9). Confirm settings 
with the button “TOOL” (10). The control unit memorizes the settings and automatically returns to normal operating mode.

4.3. CONNECTION Of hANDPIECE TO CONTROl UNIT

• The plug (26) at the end of the cable of the Handpiece has to be connected to one of the sockets “HANDPIECE 1” (2) or 
“HANDPIECE 2” (3) at the front panel of the Control Unit. Up to two Handpieces can be connected to the Control Unit at the 

same time.

• The plug (26) of the Handpiece is marked with a notch and a red dot. When connecting the plug, make sure that the red 
dot on the plug is in the same position as the red dot on sockets (2) or (3) of the Control Unit. The pins inside the plug (26) 

might otherwise get damaged.

• When the Control Unit is activated (see chapter 4.6.), the Handpiece is ready for use. The Handpiece can be operated via 

the Control Unit and/or the Footswitch. 

The Control Unit is provided with a so-called priority circuit for the Handpiece that was connected first irrespective of 
whether socket “HANDPIECE 1” (2) or “HANDPIECE 2” (3) was chosen. When two Handpieces are connected at the same 
time, activate the required Handpiece by pressing the button TOOL (10).

Содержание 16-2050





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды