background image

AXS 

 Ramp Manual 

 

 

 

AXS FL RAMP Manual rev 1 

 

22 

 

 

Place the lock plate (red part in 
picture) in the lock on the bottom 
plate and close the lock. Make 
sure the lock plate is aligned with 
the side of the bottom plate. 
Align the ramp / bottom plate 
with the rear of the vehicle floor.  
Make two centre points in the 
floor - with a drill of 8 mm drill 
through the two holes from the 
lock plate. Then remove the lock 
plate and drill with a drill of 11 
mm through the floor. 
If the ramps needs to be stowed 
at the 90 deg inside position, 
repeat this exercise in this 
position. 

Left or right version mirrored

 

Fix the lock plate(s) with enough 
spacers at the floor. Adjustment should 
be made in such a way that the bottom 
plate slides easily under the lock plate 
with very little play. 

Use the U shaped counter plates under the 
vehicle floor

 

Ramp stop / Ramp Anti rattling device. 
You  will also  need  to  install the ramp stop  at the 
door  to  prevent  the  ramp  for  rattling  or  hitting 
against the rear door/window. ` 
We  recommend  positioning  this  as  high  as 
possible at the door 

 

The bracket needs to be fitted with the 
two  rivet  nuts  M8.  (Drill  Ø11  mm 
holes).  
Position the bracket so that the rubber 
aligns with the rail of the ramp.  

Place brackets left and right

 

Adjust the brackets so the ramp is 
held tight when the door is closed. 

Содержание AR FL 210-8/2







































Отзывы: