background image

AXS 

 Ramp Manual 

 

 

 

AXS FL RAMP Manual rev 1 

 

 

3

 

Safety instructions 

 
These Safety instructions should always be with the ramp. The operator has to 
be  made  aware  of  these  instructions  before  operating  the  ramp.  Read  these 
safety instructions carefully and act on them.

 

 
The  ramp  is  constructed  as  a  boarding  device  for  passengers  in  a  wheelchair.  It  should  be  used 
accordingly by passengers and assisting persons, as long as they are not heavier than the maximum 
load, to enter or exit a minibus, van, taxi or other vehicle.

 

1.

 

Before you can operate the ramp the Vehicle must be stopped and the hand or park brake 
applied. 

2.

 

Make sure it is safe to load or unload your passengers. 

3.

 

Before operating the ramp, make sure that there  neither anyone nor any obstacle at or 
near to the ramp. Also ensure that there is neither anyone nor any obstacle outside the 
vehicle or in the path of the ramp when in motion. 

4.

 

It  is  recommended  that  the  ramp  is  operated  by  the  driver  only  or  other  qualified 
operators. 

5.

 

The driver or operator must have a clear view of the ramp when maneuvering the ramp. 

6.

 

Wheelchair  passengers  should  always  be  assisted  while  boarding  or  un-boarding  the 
vehicle. 

7.

 

The ramp platform must be kept clean and free of oil and other slippery materials. 

8.

 

If  you  have  any  questions  about  the  safe  operation  of  the  ramp,  contact  the  person 
responsible immediately. 

9.

 

Never use the ramp for any other use than as described above. 

10.

 

Never overload the ramp. 

11.

 

The ramp should be used when it is completely unfolded and firm on the ground. 

12.

 

Repair and maintenance must to be carried out by qualified and trained staff only. 

13.

 

In case of exchanged parts 

 only the original parts of the ramp must be used. 

14.

 

Always use the recommended cleaning materials. 

15.

 

Report  any  unsafe  conditions  of  the  ramp  or  problems  during  operation  to  the  ramp 
supplier. 

 

 

Содержание AR FL 210-8/2







































Отзывы: