background image

Page 10

VII. MAINTENANCE

CAUTION

Both the electrochemical cell and the alkaline batteries used in the 

CAL-101 instrument contain corrosive chemicals.  While it is not 

expected that the chemicals in the cell or alkaline batteries will leak 

during normal operation, it is recommended that both the cell and 

the batteries be removed from the instrument if it is being stored for 

periods longer than one week between use.

VIII. ACCESSORY ITEMS/ PARTS LIST 

The following items and spare parts are available for the CAL-101:

Part Number        

Description 

                           

113-0400-00        

Quick connect outlet fitting, body,  

 

 

   

 

panel 

mount

400-0000-00        

Circuit board for CAL-101  

 

 

 

   

 

Processor

400-0001-00        

Circuit board for CAL-101 Interface 

400-0002-00        

Circuit board for CAL-101 pump  

 

 

   

 

assy

510-0101-00        

Chlorine generation cell, 2 hour,  

 

 

   

 

specify 

ppm

510-0101- 05        

Hydrogen sulfide generation cell, 2  

 

 

 

 

 

 

hour, specify ppm

510-0101- 07        

Hydrogen cyanide generation cell,  

 

 

 

 

 

 

2 hour, specify ppm

510-0101-09        

Hydrogen generation cell, 2 hour,  

 

 

   

 

specify 

ppm

510-0102-00        

BUMP Chlorine generation cell, 2  

 

 

 

 

 

 

hour, specify ppm

510-0102- 05        

BUMP Hydrogen sulfide generation  

 

 

 

 

 

 

cell, 2 hour, specify ppm

510-0102- 07       

 BUMP Hydrogen cyanide  

 

 

 

 

 

 

 

generation cell, 2 hour, specify ppm

510-0102-09        

BUMP Hydrogen generation cell, 2  

 

 

 

 

 

 

hour, specify ppm

730-0101-00        

Hard-body, water proof, padded   

 

 

   

 

accessory 

case

910-0601-00        

Instruction manual, CAL-101

Содержание CAL-101
















Отзывы: