Accutech LC1400 Скачать руководство пользователя страница 29

Страница: 29 / 72

1-19

Chapter 1:

The LC1400 System

Typical LC1400 Configuration - Double Sliding Doors

LC1400T

Part #662022

Lexan Standoff

Part #200628

KP103

Keypad

Part #650209

15VDC/2A Plug-in

Power Supply

Part #500224

Magnetic Door Position Switches

Part #650514

Ferrite Bar inside

enclosure must be

min 3” from metal

frame

Mounting Screws

Ferrite Bar

inside

enclosure

must be

min 3” from

metal frame

LCT-TX

Only

Part #672022

Accutech

Important:

15VDC/2A Plug-in Power
Supply
(Part #500224):

•Installed above drop ceiling

Magnetic Door Position
Switches
(Part #650514):

•Position on latch sides of top
of doors

LC1400T / LCT-TX

•Not designed for ceilng mount.
•Position ferrite bar inside
enslosure at least 3” away from
any metal.
•Recommended distance from
door: 3” - 6” (Max. 18”)

Lexan Standoff
(Part #200628):

•Mount at breakaway door on
oposite side of sliding glass
doors.

LC1400 Double Door Kit
(Part #800127):

•LC1400T (1)
•LCT-TX (1)
•Keypad (1)
•Magnetic Switch (2)
•Cable Kit (1)
•15VDC/2A Power Supply (1)

Two Lexan Standoffs not
included, and must be
purchased seperately.

Содержание LC1400









































































Результаты поиска

Содержание LC1400

Отзывы:

Бренды по названию

Популярные бренды

Accutech LC1400, Руководство по установке

Результаты поиска

Содержание LC1400

Отзывы:

Бренды по названию

Популярные бренды