Accutech LC1400 Скачать руководство пользователя страница 28

Страница: 28 / 72

Chapter 1:

The LC1400 System

1-18

Important:

15VDC/2A Plug-in Power
Supply
(Part #500224):

•Installed above drop ceiling

Magnetic Door Position
Switch
(Part #650514):

•Position on latch side of top
of door

LC1400T / LCT-TX

•Not designed for ceilng
mount.
•Position ferrite bar inside
enclosure at least 3” away
from any metal.
•Recommended distance
from door: 3” - 6” (Max. 18”)
-Position ~2” from floor

LC Double Door Kit
(Part #800122):

•LC1400T (1)
•LCT-TX (1)
•Keypad (1)
•Magnetic Switch (2)
•Cable Kit (1)
•15VDC/2A Power Supply (1)

Two Lexan Standoffs not
included and must be
purchased seperately.

LCT-TX

Only

Part #672022

Typical LC1400 Configuration - Double Door with Outer Windows

LC1400T

Part 662022

KP103 Keypad

Part #650209

Lexan

Standoff

Part #200628

Magnetic Door Position Switches

Part #650514

15VDC/2A Plug-in

Power Supply

Part #500224

Accutech

Ferrite Bar inside

enclosure must be

min 3” from metal

frame

Ferrite Bar

inside

enclosure

must be

min 3” from

metal frame

Mounting Screws

Lorem ipsum

Содержание LC1400









































































Результаты поиска

Содержание LC1400

Отзывы:

Бренды по названию

Популярные бренды

Accutech LC1400, Руководство по установке

Результаты поиска

Содержание LC1400

Отзывы:

Бренды по названию

Популярные бренды