Accurex XRV-25 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 32

background image

Packaged Rooftop Ventilator

9

Typical Unit Installed on Rails Supplied by Others

Rail Mounting and Layout

• The units may be installed on rails provided and

installed by others. Ensure that rails are designed to
handle the weight of the unit and provide proper load
distribution on building supports.

• Make sure that rail positioning does not interfere with

the openings on the unit.

• Rails should run the width of the unit and extend

beyond the unit a minimum of 12 inches on each side.

• Set unit on rails.

Alternate Supply Entry Locations

Each installation is unique and as a result, alternate
entry locations may be ﬁeld-located. Before using any
alternate entry location, verify the suitability of the
location and ensure the use of an alternate location
does not interfere with unit wiring, components or
functionality.

Recommended Electrical and Gas
Supply Entry Locations

Manufacturer recommends that electrical service and
gas supply be brought into the cabinet through the
end wall, as shown below. There are three penetrations
into the cabinet that are required; one for high voltage
supply wiring, one for low voltage control wiring and one
for either gas supply or high voltage supply wiring for an
electric heater.

WARNING

Never drill holes in the roof of the unit! There is high
voltage wiring located between the inner and outer
roof panels. Damage to the wiring could cause severe
bodily harm or death.

Typical Gas Supply Piping Connection

Ground

Joint

Union

8 in. Trap

Gas to

Controls

From Gas Supply

Bleeder Valve or
1/8 in Plugged Tap

Gas Cock

Optional Gas Piping

Units with indirect gas-ﬁred furnaces require ﬁeld-
supplied and installed gas supply piping. The unit gas
connection is

3

⁄

4

inch NPT. The maximum allowable gas

pressure is 14 in. wg.

Gas Connections

If this unit is equipped with an indirect gas-ﬁred furnace,
connection to an appropriate gas supply line will be
required. For complete information on installation
procedures for the optional gas furnace, refer the
PVF/PVG Indirect Gas-Fired Heat Module Installation,
Operation, and Maintenance Manual.

Recommended Gas and Electric Supply Entry Locations

Optional Unit
Disconnect

Field Wiring

Indirect
Gas
Supply
Location

Installation

«
...
7
8
9
10
11
...
»

Содержание XRV-25

































Отзывы:

Нет отзывов

Похожие инструкции для XRV-25

Бренд: ValuTek Страницы: 4

ZETATOP SM 225.60B

Бренд: ZIEHL-ABEGG Страницы: 4

Бренд: ebm-papst Страницы: 7

Бренд: SystemAir Страницы: 6

Бренд: Dimplex Страницы: 9

Бренд: ebm-papst Страницы: 11

Бренд: ICC Chimney Страницы: 22

Бренд: HAMPTON BAY Страницы: 28

Бренд: Maico Страницы: 26

Бренд: ALPATEC Страницы: 34

Бренд: Kichler Lighting Страницы: 60

Бренд: NuAire Страницы: 5

Бренд: Svan Страницы: 8

Бренд: Sygonix Страницы: 80

Бренд: kincrome Страницы: 2

Бренд: NuAire Страницы: 8

Бренд: Craftmade Страницы: 22

Бренд: EuropAce Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды