Accurex XRV-25 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

background image

Packaged Rooftop Ventilator

4

Product Overview

A horizontally conﬁgured High Percentage Outdoor
Air unit designed for installation either indoors or
outdoors. Each unit has multiple options for cooling
and/or heating. The unit is designed to replace air that
is exhausted from the building and also heat and cool,
as needed. The air volume produced by the unit is
constant, but can be optionally modulated to provide a
variable air volume (VAV) and recirculation is also offered
as an option.

Cooling

Units have the following cooling options available:
• Packaged

DX

• Split

DX

• Chilled water coil
Units with packaged DX are shipped fully charged with
refrigerant and are ready for operation upon arrival.

Heating

There are three different optional heat sources that can
be ordered for this unit:
•

Indirect gas-ﬁred furnace with one or two sets of
heat exchangers

• Electric heat with inﬁnitely variable SCR control
• Hot water coil

Airﬂow Arrangement

The unit is capable of Constant Air Volume (CAV),
Variable Air Volume (VAV), 100% Outdoor Air and have
recirculating air options.

Safety Listing

Models are listed per ANSI/UL 1995, Heating and
Cooling Equipment and are ETL Certiﬁed.

Models and Capacities

The packaged rooftop ventilator is built on three
different platform sizes.

Model

Cooling Capacity

XRV-25

5 to 15 tons

XRV-45

15 to 30 tons

XRV-70

25 to 45 tons

«
...
2
3
4
5
6
...
»

Содержание XRV-25

































Отзывы:

Нет отзывов

Похожие инструкции для XRV-25

Бренд: ebm-papst Страницы: 12

Бренд: LUCCI Air Страницы: 16

Бренд: Orbegozo Страницы: 16

Бренд: Dimplex Страницы: 10

Бренд: Vent-Axia Страницы: 16

Бренд: Air King Страницы: 12

Бренд: Orbegozo Страницы: 32

Бренд: Harbor Breeze Страницы: 9

Бренд: ayas Страницы: 19

Бренд: Prima Klima Страницы: 3

Бренд: S&P Страницы: 24

Бренд: ebm-papst Страницы: 12

Бренд: FABRILAMP Страницы: 12

Бренд: Singer Страницы: 20

Бренд: oneConcept Страницы: 32

Бренд: Wahoo Страницы: 4

TURBO SILENCE VU5551U0

Бренд: Rowenta Страницы: 15

Бренд: Rubine Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды