ICC Chimney EXCELDirect Скачать руководство пользователя | Manualshive

Страница: 1 / 22

background image

EXCELDirect

®

DIRECT VENT VENTING SYSTEM

INSTALLATION AND MAINTENANCE INSTRUCTIONS

EXCELDirect

®

is a certified venting system designed to be used only with certified

direct vent gas fired appliances.

The direct vent gas appliance must be certified for use with the ICC EXCELDirect

®

venting system. Refer to the manufacturer's labeling and instruction manual to confirm
that EXCELDirect

®

is listed for use with the appliance model you have selected.

ARNING

WARNING

•

The installation must conform with local codes or, in the absence of local codes,

with the following code in force:

- National Fuel Gas Code, ANSI Z223.1 (USA) or,

- Natural Gas and Propane Installation Code, CAN/CSA B149.1 (Canada).

•

A major cause of vent related fires is failure to maintain required clearances (air

space)  to  combustible  materials.  The  venting  configurations  and  clearances
requirements are indicated in the Direct Vent gas appliance instructions manual.
It  is  of  utmost  importance  that  this  venting  system  be  installed  only  in
accordance  with  these  instructions.  Do  not  fill  the  air  space  with  insulating
material.

•

A direct vent appliance must be connected to a single venting system. Multiple

venting is not allowed.

•

Specific requirements for horizontal installation, such as minimum clearances to

balcony, window, door, soffit, etc. are detailed in this manual.

•

Contact local building or fire officials about restrictions and installation inspection

in your area.

S

Do not begin installing the ICC EXCELDirect

®

venting system until you have carefully

read the appliance and vent system installation instructions.

Use only ICC model EXCELDirect

®

components. Failure to do so will void the

certification and warranty of the product.

Keep these installation and operating instructions in a safe location for future
reference.

EXCELDirect

®

has been tested and listed to the following:

. UL 2112 Standard by Underwriters Laboratories inc. (Listing #MH300439)
. Conforms to ANSI Z21 Std for Direct vent gas appliances and UL Std 2112

by INTERTEK. (ETL Listing # 4005717)

. Certified to CSA Std for Direct vent gas appliances by INTERTEK.

(ETL Listing # 4005717)

ICC INDUSTRIAL CHIMNEY COMPANY INC.

400 J.F. Kennedy, St. Jerome

Quebec, Canada, J7Y 4B7

Tel.: (450) 565-6336, Fax: (450) 565-65 19

www.icc-rsf.com

XLT-II_2019-05

1
2
3
...
»

Содержание EXCELDirect























Отзывы:

Нет отзывов

Похожие инструкции для EXCELDirect

Бренд: Lasko Страницы: 2

Бренд: Vallox Страницы: 14

Бренд: UFESA Страницы: 40

Бренд: S&P Страницы: 64

Бренд: Parkside Страницы: 129

Бренд: ebm-papst Страницы: 5

Бренд: Kichler Lighting Страницы: 54

Бренд: Living & Co Страницы: 16

Бренд: EUROM Страницы: 48

Бренд: ebm-papst Страницы: 14

LUX CEILING Lux C 4,2W Trimless

Бренд: Nemo Studio Страницы: 4

Бренд: Fanaway Страницы: 36

Бренд: V-TAC Страницы: 172

Бренд: Zehnder Rittling Страницы: 28

Бренд: ebm-papst Страницы: 10

Бренд: Hayward Pool Products Страницы: 10

Бренд: Waves Страницы: 15

Бренд: Levoit Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды