background image

Frequently Asked Questions

What temperature is the thermostat set from the 
factory?

 95º 

Fahrenheit.

Will the temperature interlock automatically start/
stop the fans?

 

When connected properly to fan starters the 
temperature interlock will automatically control 
the fans without input from the user. However, it is 
intended to be used as a back-up to manual control.

May I connect the power going to my fan directly 
through the control box?

 

No, the control box should only use control voltage 
only (24-115 VAC), and a separate 115 VAC power 
source is required to run the temperature interlock 
controls. Accurex recommends the use of starters 
sized for each fan.

What is the purpose of the timed relay in the control 
box?

 

The timed relay is used to delay the shut down 
of the fans to prevent fan on/off cycling while the 
temperature in the exhaust duct can reach steady 
state. Without the delay, cycling could occur both on 
startup or shutdown of cooking equipment. The delay 
is typically set at 20 minutes.

Can I use one control box for multiple hood systems?

 

This can be done, however, it is not recommended. 
Any one of the thermostats would turn on all hoods 
running on that control box. It is better to have one 
hood/fan per control box, plus a significant energy 
savings can be obtained if one or more of the hoods 
is not in operation.

Can I still turn my fan on and off?

  

Yes, the temperature interlock is designed to be 
operated with a typical on/off switch. The fan may not 
turn off immediately after turning the fan switch off, it 
will sense when the cooking operations have cooled 
and then turn off.

Replacement Parts

Part 

Number

Description

383923

Thermostat, Vulcan  
1C2B9 5/8-inch Type C

451168

Evergreen Quik-Seal, 1/2-inch  
#171 (1-1/8 inch hole size)

830125

Extension, Octagon (drilled)  
SC55151-1/2 (380928)

380926

Cover, Octagon Box  
SC#54-C-1RACO 722

732396

J-Box Plate

384905

Terminal Block, Single Pole, 
DIN-RAIL MT, ABB ZS6

384908

Jumper, DIN-RAIL  
Terminal Block 2 Pole ABB JB6-2

383271

Time Delay Relay SSAC  
#KRDB424 SPST 1-100 min.

452614

Evergreen Compression Seal,  
5/8-inch, #302

Codes and Standards Compliance

• UL 

710

•  National Fire Protection Association (NFPA 96)

•  International Mechanical Code (IMC)

Temperature Interlock

11

Содержание Temperature Interlock













Отзывы: