background image

 

Accurate Technology Inc. 

Page 3 of 20 

 

FCC NOTICE 

 

This equipment has been tested and found to comply with the limits for a class 

B  digital  device,  pursuant  to  part  15  of  the  FCC  Rules.    These  limits  are 

designed  to  provide  reasonable  protection  against  harmful  interference  in  a 

residential installation.  This equipment generates, uses and can radiate radio 

frequency  energy  and  if  not  installed  and  used  in  accordance  with  the 

instructions,  may  cause  harmful  interference  to  radio  communications.  

However,  there is no guarantee that  interference  will not occur  in  a  particular 

installation.    If  this  equipment  does  cause  harmful  interference  to  radio  or 

television reception, which can be determined by turning the equipment off and 

on,  the  user  is  encouraged  to  correct  the  interference  by  one  or  more  of  the 

following measures: 

 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and the receiver. 

  Connect  the  equipment  to  an  outlet  on  a  circuit  different  from  that  to 

which the receiver is connected. 

  Consult  the  dealer  or  an  experienced  radio/television  technician  for 

help. 

 
Operation  with  non-approved  equipment  is  likely  to  result  in  interference  to 

radio and TV reception.  The user is cautioned that changes and modifications 

made to the equipment without the approval of the manufacturer could void the 

user’s authority to operate this equipment. 

Содержание ProScale





















Отзывы: