background image

 

Manual Part # 800-1403-001 Revision 06-01-2020

 

Page 5 of 16

 

Initial Setup: 

 
Follow these steps to configure your readout for initial use: 
 

1.  When the readout is first powered on, it may show a 

No Enc

 message. 

This means there is not an encoder connected to the readout. To clear 
the message, connect a compatible encoder. 

 

2.  When an encoder is first connected, the readout may show 

No Pos

This informs the user that a position has not been programmed yet. For 
the initial setup, use the DATUM, and PLUS keys to set a 

POSITIVE

 

starting value. (Any POSITIVE value will work for now.) 

 

3.  Choose the units that will be initially used (millimeters, inches, or 

fractions). Each press of the UNITS key will change the units that are 
displayed. (The screen will show the units description each time the 
UNITS key is pressed.) 

 

4.  Check the reading direction: 

a)  With the readout showing a POSITIVE number on the screen, 

move the encoder system a short distance. 

b)  Take note if the displayed value increased or decreased. 
c)  If the displayed value got larger/smaller, and this 

IS

 correct for your 

installation, no further steps are needed. 

d)  If the displayed value got larger/smaller, and this 

IS NOT

 correct for 

your installation, the reading direction needs to be reversed. This 
can be accomplished two ways: 

i. 

If your encoder system is a Model 19, 29, 190, 290, 390, or 
590 type, you can rotate the encoder 180 degrees on the 
scale. 

ii. 

If the encoder cannot be rotated, or if the encoder is a 
Model 150 or Model 250 system, the reading direction 
must be reversed using the programming mode, parameter 
Pr2. Consult the Complete User Guide at 

www.proscale.com 

or contact factory for assistance with 

this. 
 

5.  Calibrate the readout. Since there are many thousands of applications 

for ProScale systems, all calibration methods cannot be described 
here. However, the general steps are the same. 

a.  Determine what value the readout should be showing. 
b.  Use the DATUM, PLUS, and MINUS keys to adjust the reading 

on the screen to match desired value. NOTE: To rapidly adjust 
the value, press and hold the PLUS or MINUS key down. (The 
update speed will increase every 2 seconds the key is held.) 

 

 

Содержание ProScale 950 Series

















Отзывы: