background image

The suspension of this vehicle has been optimized for off road utility through installation of an AccuAir

®

 system allowing 

control/adjustment of ride height to accommodate challenging terrain & obstacles. The suspension feel and handling maybe 
different than an unmodified Jeep. 

To reduce risk of roll-over other accident & serious injury always:

• 

Inspect components including bags, lines, valves & compressor before use, followed by system self-test. Maintain & repair 

as indicated. On road height limited to approx. 3.0” by system speed & ride height sensors. 

REPLACE & DO NOT USE ON 

ROAD IF SPEED SENSOR DAMAGED/INOPERATIVE.

• 

DO NOT

 modify or substitute AccuAir

®

 components of this system. Use of oversize tire/wheel combinations may increase 

stopping distances, ride height and/or compromise performance of vehicle stability control and other systems.

CONGRATULATIONS!

A FEW WORDS ABOUT PRODUCT SAFETY

Your AccuAir

®

 Jeep JK Air Suspension system reflects a unique solution to balancing enhanced off road terrain and 

obstacle clearance with everyday drivability and ride quality. The AccuAir

®

 JK system features remote mounted seamless 

air tank, a quality compressor, mounts and all fittings necessary to replace your coil springs with ruggedly designed four 
corner air bags allowing you to select a ride height tailored to your off road adventures. Back on the road, a unique speed 
sensing value presets ride height to a maximum of 3.0” of lift (approx.), helping to preserve familiar ride comfort. Enjoy 
your AccuAir

®

 JK system by Treading Lightly

©

 and following all instructions and product safety messaging below. If you 

have further questions contact us at: 

[email protected]

. Our team is here to help. 

• 

The drag link must be adjusted to center the steering wheel before the vehicle is driven. Failure to do so will cause 
computer errors, odd handling characteristics, and poor performance.

• 

If larger tires (10% more than the OEM diameter) are installed, speedometer recalibration will be necessary. 
Contact your local Jeep dealer.

• 

After installation, a qualified alignment facility is required to align the vehicle to the OEM specification.

• 

Avoid excessive speeds, abrupt maneuvers, surfaces/obstacles 

which may induce a tripping moment. All occupants 

BUCKLE UP & 

USE

 supplemental restraints.

• 

Consult the AccuAir

®

 installation manual  

(

[email protected]

) & OEM off road supplement for additional 

safety information.

Before installation, please take a moment to review the following safety information and installation instructions. 
Important safety information is generally preceded by one of three signal words indicating the relative risk of injury.
The signal words mean:

If you have any questions or reservations about installing this product, contact AccuAir Customer Service.

WARNING:

A hazardous situation which, if not avoided, could result in death or serious injury. You 

CAN

 be 

killed

 or 

seriously 

hurt

 if you don’t follow instructions.

WARNING:

This advanced AccuAir

®

 JK kit requires professional installation, with access to vehicle lift and experience with 

Jeep JK suspension, electrical wiring, Jeep maintenance recommendations, safety messaging, torque & other 
specifications, general repair safety including personal protection, vehicle rack safety, isolation and containment of 
OEM spring assemblies during removal.

WARNING:

Wheel setup with a minimum of 4.5” of back spacing is 
required with a maximum 9” wide wheel.

WARNING:

Incorrect shock length will distort air bag placement and lead to burst or reduced service life. USE front and rear 
shock absorbers included with this kit. 

Replacement shocks must be FRONT: 26.125” (allowed variance .125”); REAR: 27.72” (allowed variance .125”).

CAUTION:

A hazardous situation which, if not avoided, could result in minor or moderate injury. You 

CAN

 be moderately 

hurt

 

and may also suffer property damage if you do not follow instructions.

CAUTION:

Risk of Eye Injury. Safety glasses, gloves & other personnel protection should be worn when working with this product.

NOTICE:

Careful attention is required to this instruction or operation but does generally not relate to personal injury. Damage to 
your AccuAir

®

 product or other property may result if you don’t follow instructions.

NOTICE:

Never lower vehicle from rack or following inspection/
repair without air bags being fully inflated.

CANCER AND REPRODUCTIVE HARM 

WWW.P65WARNING.CA.GOV

WARNING

WARNING:

SUSPENSION MODIFIED WITH VARIABLE 

HEIGHT AIRBAGS - HIGHER ROLLOVER RISK

Inspect Components Followed by 

System Self-test.

DO NOT Modify or Substitue AccuAir

®

 

Components of This System.

Avoid Excessive Speeds, Abrupt 

Maneuvers, Surfaces/Obstacles 

Which May Induce a Tipping Moment.

Always Buckle Up.

See AccuAir

®

 Installation 

Manual & OEM Off Road 

Supplement for Additional 

Safety Information

Affix warning decal on driver’s side visor in clear view 

of all occupants.

1

2

AA-4397 Installation Manual

REV 01    |    05/25/2023

PRODUCT & INSTALLATION OVERVIEW

Содержание AA-4397









































Отзывы: