Accorroni HUB RADIATOR PACK CF 3.0, Техническая информация

Страница: 16 / 48

16
Parameter
Valori impostabili Valori di default Note
P01 Boiler type selection 0 ÷ 8 0
0 = instantaneous
1 = with kettle thermostat
2 = with kettle temperature probe
3 = heating only
P02 Gas type selection
0 - 1 0
0 = natural
gas
1 = L
PG
P03 Selection type DHW control 0 - 1 1
0 = flow switch
1 = flow meter
P04
Regulation coefficient with external probe
0 ÷ 90 30
P05 Anti Fast Cycles time
0 ÷ 10 min 3
P06 1
DO NOT MODIFY
P07 Ignition Heating ramp [value 1=10s] 0 ÷ 80 12
P08 Maximum heating power selection
(PREMIX)
P10...100 70%
P09 Selection of maximum DHW power P10…100 80%
P10 Minimum power selection 0…P09 0%
P11 Minimum setpoint value selection
heating
20...P12 25°C
P12 Selection of the maximum setpoint value
heating
P11…80 80°C
P13 Selection of the maximum value of the DHW setpoint
35 ÷ 67 60°C
P14 Selection of calibration type 0 ÷ 20 0
0 = manu
5 = auto
P15
Boiler power selection
0 ÷ 4 4
0 = 24 kW
1 = 28 kW
2 = 32 kW
3 = 16 kW
4 = 20 kW
P16
Not used
P17
Not used
P18 Not used
P19 Thermostat (0) / Flue gas probe (1) 0 - 1 1
DO NOT MODIFY
P20
Selection of the minimum value of the DHW
35 ÷ 50 35
P21 Low temperature zone selection
0 - 1 0
0 =
High temperature
1 =
Low temperature
P22
Not used
P23 Selection of pump activation time
(min):
cold area
0 ÷ 10 0
P24 Child protection 0 ÷ 1 0 1 = active protection
P25
Not used
P26 Ram stroke delay selection
(sec) 0 ÷ 3 0
P27 Preheating temperature selection OFF (°C) 30 ÷ 75 45
P30
Not used
P31 Fan speed selection
(P31 x 25) rpm
80 ÷ 160 140
P32 Fan max speed selection (P32 x
25) + 2000) rpm
P33...255 170
P33 Fan minimum speed selection
(P33 x 25) 30 ÷ 60 36
P36
Not used
P37 AUX probe 3 ÷ 3 3
DO NOT MODIFY
P38 Antifreeze temperature selection
0…+10 5
P39 Post-circulation heating time selection 0 ÷ 99 sec x 10 120
P40 Ignition delay time selection heating
0 ÷ 60 sec x 5 0
P41 Sanitary modulation selection with flow meter
0 ÷ 1 1
0 =
not active
1 =
active
P42 Select enable / disable preheating function
ACS
0 ÷ 1 0
0 = disabled
1 = enabled
P43 DHW activation delay time selection with
solar configuration
0 ÷ 30 sec 0
P44 Selection of pressure sensor type 0 - 1 1
0 = pressure switch
1 = trasducer
P45 Anti-legionella function selection (cylinder only)
54, 55 ÷ 80 54
54 =
disabled
55 ÷ 80 =
delivery temperature set