WVD-S600SM
Quick Reference Guide
WVD-S600SM, Rev A
Page 1
S600SM S
ENSOR
O
VERVIEW
:
The S600SM is a surface mount sensor that can be
placed on top of the driveway to detect vehicles. The
S600SM does not require any holes to be drilled and
can be installed with epoxy or anchor bolts saving
installation time and labor.
For complete installation guidelines, download
the WVD100 Installation & Program Manual at
www.AccessOneTechnologies.com
S
ENSOR
L
EARN
B
UTTON
:
To access the sensor learn button for programming:
1. Remove the eight screws holding the top of the
housing to the housing base.
2. Remove the mounting strap and screw.
3. Pull the Sensor board up and the learn button is on
the front side.
IMPORTANT:
The Sensor board and antenna are installed face
down allowing them to point upward when the base
plate is installed and the sensor is turned upright.
A
SSEMBLING
T
HE
S
ENSOR
:
The S600SM includes a battery, Sensor board,
antenna, and mounting strap. To assemble the
sensor:
1. Turn the top cover upside down.
2. Place the battery in the battery compartment with
the battery wires going through the slot to reach
the Sensor board.
3. Place the antenna face down in the antenna
compartment with the antenna wire going through
the slot to the Sensor board. (Green back of the
antenna should be seen).
4. Place the Sensor board face down in the
compartment with the battery wires and antenna
wires going through each slot. (Back of Sensor
board should be seen).
5. Place the foam spacer on top of the antenna and
install the mounting strap over the Sensor board
and antenna/foam with the 4-40 screw.
6. Place the base plate on top of the housing cover
and check to make sure everything fits and
nothing will stop the baseplate and cover from
sealing. Only the O-ring should cause separation
and seal cleanly when the parts are connected.
7. Turn the baseplate and cover upright and install
the 8 screws to seal the housing. IMPORTANT:
The baseplate and cover must seal together
tight to prevent any water from entering the
housing.
Mounting
Strap &
Screw
WVD-S600SM
Quick Reference Guide
WVD-S600SM, Rev A
Page 2
S
ENSOR
D
IRECTION
:
The detection area is rectangular and is approx. 8ft
wide x 4ft deep. To properly orientate the sensor,
direction arrows are located on the baseplate and
sensor cover.
1. Locate the direction arrows on the sensor cover.
2.
Point the direction arrows toward the gate parallel
with the line of traffic.
I
NSTALLING
T
HE
S
ENSOR
W
ITH
E
POXY
:
The sensor can be secured to the driveway with
screw anchors or a standard concrete epoxy. To
mount the sensor using epoxy:
1. Select the sensor location and test the sensor
before securing it. Make sure it tests properly and
drops detect in the full open or full closed position.
2. Using an epoxy such as Loctite or JB Weld,
spread the epoxy on the bottom of the baseplate
and press to the driveway.
I
NSTALLING
T
HE
S
ENSOR
W
ITH
A
NCHORS
:
The sensor can be secured to the driveway with four
1/4” Flat Head Sleeve Anchors. To mount the sensor
using anchors:
1.
Select the sensor location and test the sensor
before securing it. Make sure it tests properly and
drops detect in the full open or full closed position.
2. Open the sensor and locate the four anchor
mounting holes on the baseplate.
3. Drill out the holes on the baseplate so the anchor
screw can pass through. Then mark the location
of each hole.
4. Drill and clean the anchor holes.
5. Drive the anchor though the baseplate and into
the anchor hole and tighten the anchor screw until
the baseplate is secure.
6. IMPORTANT: The anchor screws must be
tightened all the way down and cannot stick up
above the top of the baseplate. If it is not, it will
not allow the unit to seal properly.
Driveway
Anchor
Hole
Anchor
Hole
CORRECT:
Flush or below
INCORRECT:
Not Flush or below