background image

INTRODUCTION

Thank you for buying a spa equipped with a SmarTouch Digital con-
trol system. Many years of experience went into the design of this
family of controls. You can be assured your spa control system is the
most advanced, it is highly reliable and will serve you for many years
to come.

The control system has been designed with you, the user in mind. It
is very easy to operate and requires a minimal effort on your part.
You may use it just as it comes to you and without any programming.
Yet you have the option of getting deeply involved in the inner work-
ings of the control if you so choose. You can custom tailor it to fit
your needs.

Please take the time to read at least the first section (next page) “IN
A HURRY – READ THIS” portion of the manual before starting to use
your spa for the first time. You can familiarize yourself with the rest
of the manual at your leisure.

The more efficient the system is the

less energy it uses.

The concept behind SmarTouch Digital is to maintain the desired
temperature setting and water filtration with the least amount of en-
ergy consumption.

Temperature and Overheat sensors are located at the Stainless Steel
heater manifold, the coldest and hottest spot where true tempera-
ture is measured and to detect Freeze and Overheat conditions.

Considering the large volume of cooler water in the plumbing, pump
and heater manifold, low speed primary pump is activated for five
minutes every three hours to stabilize spa temperature, prior to ac-
tivating the heater. Estimated 102F water temperature drop at 55F
ambient air temperature is about half a degree Fahrenheit in a well
insulated spa. Heater will not start at this point until next cycle. Tem-
perature must drop by 1F before heater is activated.

Page 3

Page 24

Содержание SmarTouch Digital





























Отзывы: