background image

Time Of Day (TOD)

SmarTouch Digital maintains a 12 hour AM / PM internal real time
clock  TOD (Time Of Day). The clock based on the line frequency.
There is no battery backup and whenever the power is turned off,
TOD is no longer correct. It defaults to 12:00 AM whenever the power
is turned on.

Setting TOD is only necessary if you are going to program the filtration
and  silence cycles. If  you use the factory default settings then you do
not need to set TOD.

If you set TOD then SmarTouch will display time every first 10
seconds of each minute. If TOD has not been set then it will not be
displayed.

Setting TOD

1. Press and hold the TIME key for 2 seconds.  Current TOD will

be displayed with the hour portion flashing.

2. Release the TIME key.

3. Using the TEMP and TIME keys scroll up and down to the

desired hour. - Notice the AM / PM Led.

4. When the correct hour and AM / PM are displayed press the

SET key to lock in the new hour.

5. The display will now flash the minutes portion of current TOD.

6. Using TIME and TEMP scroll to the desired minutes.

7. When the correct minutes are displayed press the SET key to

lock in the time of day (hours and minutes)

Note : TOD is the only parameter in SmarTouch Digital that is not
preserved on power down. On power up it will default to 12:00 AM, all
other parameters are  restored to the their last setting.

Every time the controller is powered up, the microprocessor
automatically measures and determines whether the line frequency is
50 or 60 cycles in order to maintain the correct TOD.

Page  6

Содержание SmarTouch Digital series





























Отзывы: