Abit IS7-G страница 70 Скачать руководство пользователя

Страница: 70 / 110

3-16

Chapter 3

SuperIO Device:

Click <Enter> key to enter its submenu:

Onboard FDC Controller:

This option enables or disables the onboard FDC controller.

Onboard Serial Port:

This item determines which I/O addresses the onboard Serial Port controller will access.

[Auto]:

The system automatically select an I/O address for the onboard Serial Port.

[3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]:

Allows you to manually select an I/O address for the

onboard Serial Port.

[Disabled]:

Disables the onboard Serial Port.

Onboard IR Port: (For IS7-G, IS7, IS7-E, and IS7-M only)

This item determines which I/O addresses the onboard IR Port controller will access.

[Auto]:

The system automatically select an I/O address for the onboard IR Port.

[3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]:

Allows you to manually select an I/O address for the

onboard IR Port.

[Disabled]:

Disables the onboard IR Port.

UART Mode Select:

This item selects the Infrared (IR) function mode.

RxD, TxD Active:

This item sets the IR transmission/reception polarity.

IR Transmission Delay:

This option enables or disables the IR transmission delay. When set to [Enabled], the transmission will be
slower. This is recommended when transmission problem arise.

IS7 Series

Содержание IS7-G















































































































Результаты поиска

Содержание IS7-G

Отзывы:

Похожие инструкции для IS7-G

Бренды по названию

Популярные бренды

Abit IS7-G, Руководство пользователя

Результаты поиска

Содержание IS7-G

Отзывы:

Похожие инструкции для IS7-G

Бренды по названию

Популярные бренды