Abit IS7-G Скачать руководство пользователя

Страница: 63 / 110

BIOS Setup

3-9

Report No FDD For OS:

When set to [Yes], this item allows you to run some older operating system without floppy disk drive.
Leave this item to its default setting.

Delay IDE Initial (Secs):

This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A
larger value will give more delay time to the device for which to initialize and to prepare for activation.

Intel OnScreen Branding:

This item determines whether to display the “Intel Inside” logo or not at system boots up.

Disable Unused PCI Clock:

This option disables the clock of PCI slot that is not in use.

[Yes]:

The system automatically detect the unused DIMM and PCI slots, and stop sending clock signal to

these unused PCI slots.

[No]:

The system always send clock signal to all PCI slots.

NOTE:

Set this option to [No] setting if there are adapters that cannot be automatically detected by the

system and will cause malfunction.

User’s Manual

Содержание IS7-G















































































































Результаты поиска

Содержание IS7-G

Отзывы:

Похожие инструкции для IS7-G

Бренды по названию

Популярные бренды

Abit IS7-G, Руководство пользователя

Результаты поиска

Содержание IS7-G

Отзывы:

Похожие инструкции для IS7-G

Бренды по названию

Популярные бренды