Abit AB-BF6 Скачать руководство пользователя страница 53

Страница: 53 / 106

Introduction of the BIOS

3-25

User’s Manual

✏

Master/Slave Drive Ultra DMA:

Two options are available: Auto and Disabled. The default setting is

Auto

. Ultra DMA is a

DMA data transfer protocol that utilizes ATA commands and the ATA bus to allow DMA

commands to transfer data at a maximum burst rate of 33 MB/sec.

Ultra DMA/33 or Ultra DMA/66 implementation is possible only if your IDE hard drive

supports it and the operating environment includes a DMA driver (Windows

95 OSR2 or a

third-party IDE bus master driver).

➤

Auto:

If your hard drive and your system software both support Ultra DMA/33, select

Auto

to enable BIOS support. For Ultra DMA/66 devices, please refer the

requirements mentioned in page 2-18. (Default setting)

➤

Disabled: If you encounter a problem in using Ultra DMA devices, you can try to disable

this item.

Onboard IDE-2 Controller:

Description is same as the

Onboard IDE-1 Controller.

USB Keyboard Support:

Two options are available: Enabled and Disabled. The default setting is

Disabled.

If your

system contains a USB keyboard, set it to

Enabled

Init Display First

This item allows you to decide to active whether PCI slot or AGP slot VGA first.

Ultra DMA-66 IDE Controller

This item is only for the ABIT’s BE6-II motherboard. Please leave it on the default setting.

IDE HDD Block Mode:

Block mode is also called block transfer, multiple commands, or multiple sector read/write.

If your IDE hard drive supports block mode (most new drives do), select

Enabled

for

automatic detection of the optimal number of block read/writes per sector the drive can

support. The default setting is

Enabled.

Содержание AB-BF6











































































































Результаты поиска

Содержание AB-BF6

Отзывы:

Похожие инструкции для AB-BF6

Бренды по названию

Популярные бренды

Abit AB-BF6, Руководство пользователя

Результаты поиска

Содержание AB-BF6

Отзывы:

Похожие инструкции для AB-BF6

Бренды по названию

Популярные бренды