Abit AB-BF6 Скачать руководство пользователя страница 65

Страница: 65 / 106

Introduction of the BIOS

3-37

User’s Manual

3-7. PnP/PCI Configurations

This section describes configuring the PCI bus system. PCI, or

ersonal

omputer

nterconnect, is a system which allows I/O devices to operate at speeds nearing the speed the

CPU itself uses when communicating with its own special components. This section covers

some very technical items and it is strongly recommended that only experienced users

should make any changes to the default settings.

Figure 3-9. PnP/PCI Configurations Setup Screen Shot

PNP OS Installed:

The device resource assigned by PnP OS (e.g., Windows 95) or BIOS.

Force Update ESCD

Two options are available: Enabled and Disabled. Default setting is

Disabled

. Normally, you

leave this field

Disabled

. Select

Enabled

to reset Extended System Configuration Data

(ESCD) when you exit Setup if you have installed a new add-on card and the system

reconfiguration has caused a resource conflict that the operating system can not boot.

Resources Controlled By:

Two options are available: Auto(ESCD) and Manual. Default setting is

Auto(ESCD)

. When

the setting is Auto(ESCD), the

IRQ Resources

and

Memory Resources

can not be changed

Содержание AB-BF6











































































































Результаты поиска

Содержание AB-BF6

Отзывы:

Похожие инструкции для AB-BF6

Бренды по названию

Популярные бренды

Abit AB-BF6, Руководство пользователя

Результаты поиска

Содержание AB-BF6

Отзывы:

Похожие инструкции для AB-BF6

Бренды по названию

Популярные бренды