3-18
Chapter 3
NOTE:
The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or
USB type. Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of
your keyboard are too old, it may fail to power on.
KB Power ON Password:
This item sets the password required in order to power on your computer.
NOTE:
Do not forget your password, or you will have to clear the CMOS and reset all parameters in
order to utilize this function again.
Hot Key Power ON:
This item powers on the system by pressing <Ctrl> key plus one of each function key (<F1> ~ <F12>)
simultaneously.
Restore On AC After Power Loss:
This item selects the system action after an AC power failure.
[Power Off]:
When power returns after an AC power failure, the system’s power remains off. You must
press the Power button to power-on the system.
[Power On]:
When power returns after an AC power failure, the system’s power will be powered on
automatically.
[Last State]:
When power returns after an AC power failure, the system will return to the state where you
left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when AC power failure occurs, the system
will power-on when power returns.
Power Button Function:
This item selects the method of powering off your system:
[Delay 4 Sec.]:
Pushing the power button for more than 4 seconds will power off the system. This will
prevent the system from powering off in case you accidentally hit or pushed the power button.
[Instant-Off]:
Pressing and then releasing the power button at once will immediately power off the
system.
CPU THRM-Throttling
This item controls the CPU speed by cutting down its regular power to a percentage during the STR
(Suspend To RAM) state.
WakeUp by PME# of PCI:
When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will
cause the system to wake up. The PCI card must support the wake up function.
WakeUp by Onboard Lan:
When set to [Enabled], you can remotely wake up a PC in Soft-Off condition via a LAN card that support
the wake up function.
WakeUp by Alarm:
When set to [
Enabled
], you can set the date and time you would like the Soft-Off PC to power-on in the
AI7/AI7-G
Содержание AB-AI7
