ÉTAPE 14
Ouvrir le KIT DE RETENUE ANTI-BASCULEMENT POUR MOBILIER (97)
et fi xer la SANGLE DE SÉCURITÉ au DESSUS (D2). Utiliser la VIS TÊTE
LARGE 14 mm NOIRE fourni.
REMARQUE : Placer la SANGLE DE SÉCURITÉ exactement comme
l'indique le schéma.
Fixer le DESSUS (D2) aux EXTRÉMITÉS (A et B) et au
MONTANT (C). Serrer six FIXATIONS
.
Fixer la MOULURE DE DESSUS (S) au DESSUS (D2). Utiliser deux
VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES
EN MÉTAL sur la MOULURE et dans le DESSUS.
ÉTAPE 13
Attention: Examiner bien les pièces avant d'assembler. Il est
diffi cile de séparer des pièces une fois encollées.
Tout d’abord, remplir les trous dans la PLINTHE AVANT (M) de 1/4
à 1/2 pleins de COLLE (54M). Insérer ensuite les CHEVILLES EN
BOIS (15F) dans les trous. Nettoyer l'excès de COLLE.
REMARQUE : S’assurer de utiliser les trous exacts indiqués.
Maintenant, remplir le trou dans le PIED AVANT GAUCHE (J) de
1/4 à 1/2 pleins de COLLE.
Fixer la PLINTHE AVANT (M) au PIED AVANT GAUCHE (J). Serrer
un EXCENTRIQUE ESCAMOTABLE.
REMARQUE : S'assurer de bien insérer la CHEVILLE EN BOIS
située sur la PLINTHE AVANT dans le trou du PIED. Nettoyer
l'excès de COLLE.
Remplir les trous dans les PIEDS (I et K) sur l'EXTRÉMITÉ DROITE (A)
de 1/4 à 1/2 pleins de COLLE.
Fixer l'EXTRÉMITÉ DROITE (A) et PIEDS (I et K) au DESSOUS (E2),
aux PLINTHES (M et N2), à la MOULURE DE DESSOUS (P) et à la
MOULURE DE DESSUS (S). Serrer deux FIXATIONS
et cinq EXCENTRIQUES ESCAMOTABLES.
REMARQUE : S’assurer de bien insérer les CHEVILLES EN BOIS des
PLINTHES et MOULURE DE DESSOUS dans les trous des PIEDS.
ÉTAPE 12
Fixer quatre CONSOLES EN MÉTAL (4G) à la MOULURE DE
DESSOUS (P) et à la MOULURE DE DESSUS (S). Utiliser quatre
VIS TÊTE LARGE 14 mm NOIRES (1S).
Fixer la MOULURE DE DESSOUS (P) et la MOULURE DE DESSUS (S)
au PIED AVANT GAUCHE (J) sur l’EXTRÉMITÉ GAUCHE (B). Serrer
deux EXCENTRIQUES ESCAMOTABLES.
Fixer la MOULURE DE DESSOUS (P) au DESSOUS (E2). Utiliser
deux VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les
CONSOLES EN MÉTAL situées sur la MOULURE DE DESSOUS, et
dans le DESSOUS.
ÉTAPE 11
Attention: Examiner bien les pièces avant d'assembler. Il est
diffi cile de séparer des pièces une fois encollées.
Fixer deux CONSOLES EN MÉTAL (4G) à la PLINTHE ARRIÈRE (N2).
Utiliser deux VIS TÊTE LARGE 14 mm NOIRES (1S).
REMARQUE : S'assurer que les CONSOLES sont à fl eur de chant
de la PLINTHE ARRIÈRE.
Remplir les trous dans la PLINTHE ARRIÈRE (N2) de 1/4 à 1/2
pleins de COLLE (54M). Insérer ensuite deux CHEVILLES EN
BOIS (15F) dans les trous. Nettoyer l'excès de COLLE.
Maintenant, remplir le trou dans le PIED ARRIÈRE GAUCHE (L) de 1/4
à 1/2 pleins de COLLE. Insérer ensuite la CHEVILLE EN BOIS dans la
LAMBREQUIN ARRIÈRE dans ce trou. Nettoyer l'excès de COLLE.
REMARQUE : S'assurer que les VIS D'EXCENTRIQUE du PIED
s'insèrent dans les trous dans la PLINTHE ARRIÈRE. Serrer ces
deux EXCENTRIQUES ESCAMOTABLES à ce stade.
Fixer la PLINTHE ARRIÈRE (N2) au DESSOUS (E2). Utiliser deux
VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES
EN MÉTAL situées sur la PLINTHE ARRIÈRE, et dans le DESSOUS.
ÉTAPE 10
Fixer le MONTANT (C) au DESSOUS (E2). Utiliser deux VIS TÊTE
PLATE 49 mm NOIRES (113S).
ÉTAPE 9
Fixer les ENTRETOISES (T) au DESSOUS (E2). Utiliser quatre VIS
TÊTE PLATE 38 mm MARRON (14S).
Attention: Ne pas relever l'élément dans sa position verticale
avant d'avoir fi xé l’ARRIÈRE. L'élément risque de s'eff ondrer.
Fixer le DESSOUS (E2) à l'EXTRÉMITÉ GAUCHE (B). Serrer deux
FIXATIONS
Utilisation de la FIXATION
1. Insérer l'extrémité fi letée de la FIXATION dans le trou de la
pièce attenante.
REMARQUE : L'extrémité fi letée de la FIXATION doit rester
complètement insérée dans le trou de la pièce attenante lorsque
l'on bloque la FIXATION.
2. Bien serrer la FIXATION à l'aide d'un tournevis Phillips.
Page 27