manualshive.com logo in svg

ABB UNO-DM-2.0-TL-PLUS, Руководство пользователя, Страница: 77 / 198

Поделиться
Скачать
ABB UNO-DM-2.0-TL-PLUS Скачать руководство пользователя страница 77

- 77 -

000995AG

5 - Installation

I

nstallation of the external protective grounding cable

In addition to the grounding protection previously connected to the AC 

output connector, a second protective grounding cable has to be installed 

to be connected to the metal frame of the inverter.

The cable to be used must be copper and have a minimum cross-section 

not less than the phase cable and in any case not less than 4mm².

To install a second protective grounding cable, follow the procedure de-

scribed below:

• From among the components supplied, find the M5x10 screw and the 

two M5 knurled washers.

• Fit a proper cable lug on the protective grounding cable. 

• Fasten the cable lug using the screw and the two washers, following the 

sequence illustrated below and tightening to a torque of 4.1 Nm.

The connection point 

19

 is located on the underside of the inverter.

Содержание UNO-DM-2.0-TL-PLUS







































































































































































































Отзывы:

Нет отзывов