manualshive.com logo in svg

ABB UNO-DM-2.0-TL-PLUS, Руководство пользователя, Страница: 163 / 198

Поделиться
Скачать
ABB UNO-DM-2.0-TL-PLUS Скачать руководство пользователя страница 163

- 163 -

001004AG

8 - Maintenance

5.  Operations on External DC switches (if present)

Note:

 In case of absence of External DC disconnect device skip this step.

The diagram below represents a possible arrangement of the PV plant. 

Depending on the design choices made by the developer of the plant 

some of the devices could not be present. Identify the external DC 

switch(es) in the plant with the support of the plant manager.

PV Strings

External DC

Switch

Internal DC

Switch

OPEN+LOTO

External LV

AC Switch

External Main LV

AC Switch

MW Switch

LV/MW

Transformer

OPEN+LOTO

INVERTER 1

(Unit under service)

PV Strings

External DC

Switch

INVERTER 2

External LV

AC Switch

LV Distriubution

Panel

Internal DC

Switch

 

•

 

 

Open the external DC disconnect switch (blue in below picture) 

outside the inverter (IEC 60364-7-712.536.2.2)

 

•

 

 

Affix  designated  lock  preventing  operation  onto  any  external  DC 

disconnect device, affixing designated tags (LOTO procedure).

Identification of the external switch may require the cooperation of the plant manager and it 

must be included in the switching plan defined during the preparation of the work.

 

•

 

 

Check on the status LEDs 

06

 

the shutdown command has been 

carried out (Missing DC voltage status): 

All LEDs OFF

.

The time needed for the complete shut-down of the LEDs depends by the input voltage of the 

inverter. The complete shut-down of the LEDs may require some minutes.

Содержание UNO-DM-2.0-TL-PLUS







































































































































































































Отзывы:

Нет отзывов