ABB SPAU 140 C Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 72

background image

9

pulse

cond13

CS13

BS13

CB13

t < t

Fig. 6. Determination of the maximum length of the closing signal.

The maximum length of the closing signal is
determined by the setting t

pulse

. If the external

command signal disappears during the closing
operation the closing signal delivered from the
stage also resets, however, in such a way that
the closing signal is at least 100 ms, approxi-

mately. If the external command signal is active
for a longer time than the setting value t

pulse

,

the closing signal resets after the set maximum
time has elapsed. (Note! Alarm CSF13 in fig-
ure 7).

Fig. 7. Determination of the alarm limit for a still active command signal.

The setting of the pulse length can also be used
for determining the alarm limit for a command
signal that has remained active. The alarm is
only important in systems according to figure
5, where the duration of the closing signal al-
ways is shorter than the set t

pulse

time. The con-

trol module receives information about the cir-
cuit breaker status and thus is able to adjust the
command signal to be delivered to the synchro-
check relay and at the same time the length of
the closing signal. If the external command sig-
nal CS13 still is active when the closing signal
resets after the set maximum t

pulse

time, the

alarm CSF13 is activated. The alarm indicates
that the control module has not removed the
external command signal after the closing op-
eration has been performed within the prede-
termined t

pulse

time. When the duration of a

standard external command signal constantly
exceeds the maximum length of the set closing
signal under normal closing conditions, the
alarm shall be disconnected to avoid unneces-
sary alarms. The alarm can be enabled or disa-
bled by means of the functional switchgroup
SGR.

t = t

cond13

CS13

BS13

CB13

CSF13

pulse

«
...
27
28
29
30
31
...
»

Содержание SPAU 140 C









































































Отзывы:

Нет отзывов

Похожие инструкции для SPAU 140 C

Бренд: ZiFiSense Страницы: 15

Бренд: I-Gard Страницы: 28

EU400 NA-protection

Бренд: hager Страницы: 44

Бренд: Westinghouse Страницы: 114

Бренд: Westinghouse Страницы: 178

Бренд: VERIS INDUSTRIES, INC. Страницы: 2

Бренд: Extron electronics Страницы: 6

Бренд: Federal Signal Corporation Страницы: 20

Бренд: EnPointe Страницы: 5

Бренд: Robertshaw Страницы: 8

Бренд: Zamel Страницы: 2

Бренд: Pontec Страницы: 111

VOLUME BOOSTER VB04

Бренд: SITECNA Страницы: 12

VARkombi-12-PC-TFT-OG

Бренд: KAEL Muhendislik Elektronik Страницы: 32

Бренд: Viking Страницы: 2

Бренд: ABB Страницы: 140

Cutler-Hammer FP-6000 Series

Бренд: Eaton Страницы: 228

Бренд: ABB Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды