ABB SensyMaster FMT230 Скачать руководство пользователя страница 87

Страница: 87 / 112

SensyMaster FMT230, FMT250

THERMAL MASS FLOWMETER | OI/FMT230/250-EN REV. C

Modbus register
address

Parameter name

Data type [register length] /
value range

Description

Setting of the simulated measured values. The simulated value is selected with the parameter ‘Simulation Switch’.
4003

Dig.Out 41/42 State

TUSIGN8 [1]

0 - Off
1 - On

The respective simulated output value is dependent on the operating mode (pulse
/ frequency) of the digital output 41 / 42.

5017 Freq.Out

41/42

Puls.Out 41/42

TFLOAT [2]

0 to 10500 Hz 0 to 10500 pulses

4004 Dig.Out

51/52

State

TUSIGN8 [1]

0 - Off
1 - On

5019 Dig.Out

51/52

Pulse

TFLOAT [2]

0 to 10500 pulses

Only if the digital output 51 / 52 has been configured as a pulse output.

5003

Mass Flow [unit]

TFLOAT [2]

0 to 2 x QmMax DN

Setting of the simulated measured values. The simulated value is selected with
the parameter ‘Simulation Switch’.

5011

Mass Flow [%]

TFLOAT [2]

-200 to 200 %

5007 Qv@

Vol.flow

[unit]

TFLOAT [2]

0 to 2 x QvMax DN

5015 Qv@

Vol.flow

[%]

TFLOAT [2]

-200 to 200 %

5001 Temperature

[unit]

TFLOAT [2]

−

100 to 250 °C

5009 Temperature

[%]

TFLOAT [2]

-200 to 200 %

... / ...Output Readings

239 Freq.Out

41/42

TFLOAT [2]

0 to 10500 Hz

Output of the current output values. The available values are dependent on the
configuration of the digital outputs.
The parameters are read only.

Dig.Out 41/42 State

TUSIGN8 [1]

0 - Off
1 - On

241 Freq.Out

51/52

TFLOAT [2]

0 to 10500 Hz

19 Dig.Out

51/52

State

TUSIGN8 [1]

0 - Off
1 - On

Содержание SensyMaster FMT230

















































































































Результаты поиска

Содержание SensyMaster FMT230

Отзывы:

Бренды по названию

Популярные бренды

ABB SensyMaster FMT230, Инструкция по эксплуатации

Результаты поиска

Содержание SensyMaster FMT230

Отзывы:

Бренды по названию

Популярные бренды