manualshive.com logo in svg

ABB SensyMaster FMT230, Инструкция по эксплуатации

Поделиться
Скачать
ABB SensyMaster FMT230 Скачать руководство пользователя страница 40

40 

SensyMaster FMT230, FMT250

 THERMAL MASS FLOWMETER  |  OI/FMT230/250-EN REV. C 

 

 

… 6  Installation 

… Installation / Disassembly of the sensor in connection with the hot tap fitting 

 

Disassembly of the sensor

 

 

 DANGER 

Danger to life due to leaking measuring medium! 

Depending on the pressure in the piping, up to one liter of 
measuring medium can escape during disassembly of the 
sensor.  
•  Make sure that no hazardous atmosphere results from the 

escaping medium. 

•  Use safety equipment appropriate to the medium 

(poisonous, explosive, flammable, corrosive, toxic, etc.) 

 

 DANGER 

Danger to life! 

Danger to life due to leaking measuring medium from the 
disassembled sensor and the piping in operation. 
•  Secure the hot tap fitting against unintended use with a 

blind flange. 

•  Attach a warning label. 

 

Initial position 

 

Figure 29:  Integrated hot tap fitting in measurement position 

 
The integrated hot tap fitting is in the measurement position, 
the sensor element fully protrudes in the piping cross-section. 
 

 

Disassembly of the sensor 

 

Figure 30:  Setting the integrated hot tap fitting in disassembly position 

 
1.

Disconnect the electrical connections on the sensor. 

2.

Turn the sensor with the union nut 

1

 in the disassembly 

position. The lower edge of the union nut indicates the 
position of the sensor. The sensor will not be in the 
disassemble position 

0 - CLOSE - ZU

and the hot tap fitting 

will not be gasketed from the process 

2

 until the 

disassembly position is reached (the upper limit stop of the 
union nut). 

 

Figure 31:  Loosening the cap nuts of the protection cap 

 
3.  Screw off the cap nuts 

1

 and washers of the protection cap. 

 

 

Содержание SensyMaster FMT230

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды