background image

4 SCC-K 

NO

2

/ NO Converter Operator’s Manual 

42/23-52 EN Rev. 2 

General Safety Information 

  

Requirements for 
Safe Operation 

In order to operate in a safe and efficient manner the instrument should be 
properly handled and stored, correctly installed and started, properly operated 
and correctly maintained. 

  

Personnel 
Qualifications 

Only persons familiar with the installation, set-up, operation and maintenance of 
comparable equipment and certified as being capable of such work should work 
on the instrument. 

  

Special Information 
and Precautions 

These include 

  The content of this operator’s manual. 

  The safety information affixed to the instrument. 

  The applicable safety precautions for installing and operating electrical devices 

  Safety precautions for working with gases, acids, condensates, etc. 

  

National Regulations 

The regulations, standards and guidelines cited in this operator’s manual are 
applicable in the Federal Republic of Germany. The applicable national regulations 
should be followed when the instrument is used in other countries. 

  

Instrument Safety 
and Safe Operation 

The instrument is designed and tested in accordance with EN 61010 Part 1, 
“Safety Provisions for Electrical Measuring, Control, Regulation and Laboratory 
Instruments” and has been shipped ready for safe operation. 

 
To maintain this condition and to assure safe operation, read and follow the safety 
information identified with the 

 symbol in this manual. Failure to do so can put 

persons at risk and can lead to instrument damage as well as damage to other 
systems and instruments. 

  

Additional 
Information 

If the information in this operator’s manual does not cover a particular situation, 
ABB Automation Service is prepared to supply additional information as needed.  

 
Contact your local ABB Automation service representative or 

 
ABB Automation Service, Post Office Box 93 02 09, D-60457 Frankfurt  
Telephone  +49-69-79 30-46 00,  Fax  +49-69-79 30-46 01, 
E-mail: [email protected] 

  

Содержание SCC-K

























Отзывы: