ABB REU615 Скачать руководство пользователя страница 18

Страница: 18 / 80

•

IED User Management

•

Application Configuration

•

Graphical Display Editor

Download connectivity packages from the ABB web site

http://

www.abb.com/substationautomation

2.2

Operation functionality

2.2.1

Optional functions

•

Arc protection (configuration A only)

•

Modbus TCP/IP or RTU/ASCII

•

IEC 60870-5-103

•

DNP3 TCP/IP or serial

•

RTD/mA measurements and multi-purpose protection (configuration B only)

2.3

Physical hardware

The IED consists of two main parts: plug-in unit and case. The content depends on
the ordered functionality.

Table 2:

Plug-in unit and case

Main

Slot ID

Content options

Plug-in

unit

HMI

Small (4 lines, 16 characters)

Large (8 lines, 16 characters)

X100

Auxiliary power/BO

module

48-250V DC/100-240 V AC; or 24-60 V DC

2 normally-open PO contacts

1 change-over SO contacts

1 normally open SO contact

2 double-pole PO contacts with TCS

1 dedicated internal fault output contact

X110

BIO module

8 binary inputs

4 signal output contacts

X120

AI/BI module

Only with configuration B:

3 phase current inputs (1/5 A)

1 residual current input (1/5 A)

3 phase voltage inputs (60-210 V)

Table continues on next page

Section 2

1MRS757054 A

REU615 overview

REU615

Application Manual

Содержание REU615
















































































Результаты поиска

Содержание REU615

Отзывы:

Бренды по названию

Популярные бренды

ABB REU615, Руководство по применению

Результаты поиска

Содержание REU615

Отзывы:

Бренды по названию

Популярные бренды