ABB REU615 Скачать руководство пользователя страница 13

Страница: 13 / 80

1.4.2

Manual conventions

Conventions used in IED manuals. A particular convention may not be used in this
manual.

•

Abbreviations and acronyms in this manual are spelled out in the glossary. The
glossary also contains definitions of important terms.

•

Push button navigation in the LHMI menu structure is presented by using the
push button icons, for example:
To navigate between the options, use

and

•

HMI menu paths are presented in bold, for example:
Select

Main menu/Settings

•

LHMI messages are shown in Courier font, for example:
To save the changes in non-volatile memory, select

Yes

and press

•

Parameter names are shown in italics, for example:
The function can be enabled and disabled with the

Operation

setting.

•

Parameter values are indicated with quotation marks, for example:
The corresponding parameter values are "On" and "Off".

•

IED input/output messages and monitored data names are shown in Courier
font, for example:
When the function starts, the

START

output is set to TRUE.

1.4.3

Functions, codes and symbols

Table 1:

REU615 Functions, codes and symbols

Function

IEC 61850

IEC 60617

IEC-ANSI

Protection
Three-phase non-directional

overcurrent protection, low stage,

instance 1

PHLPTOC1

3I> (1)

51P-1 (1)

Three-phase non-directional

overcurrent protection, high stage,

instance 1

PHHPTOC1

3I>> (1)

51P-2 (1)

Three-phase non-directional

overcurrent protection,

instantaneous stage, instance 1

PHIPTOC1

3I>>> (1)

50P/51P (1)

Residual overvoltage protection,

instance 1

ROVPTOV1

Uo> (1)

59G (1)

Residual overvoltage protection,

instance 2

ROVPTOV2

Uo> (2)

59G (2)

Residual overvoltage protection,

instance 3

ROVPTOV3

Uo> (3)

59G (3)

Three-phase undervoltage

protection, instance 1

PHPTUV1

3U< (1)

27 (1)

Three-phase undervoltage

protection, instance 2

PHPTUV2

3U< (2)

27 (2)

Three-phase undervoltage

protection, instance 3

PHPTUV3

3U< (3)

27 (3)

Table continues on next page

1MRS757054 A

Section 1

Introduction

REU615

Application Manual

Содержание REU615
















































































Результаты поиска

Содержание REU615

Отзывы:

Бренды по названию

Популярные бренды

ABB REU615, Руководство по применению

Результаты поиска

Содержание REU615

Отзывы:

Бренды по названию

Популярные бренды