manualshive.com logo in svg

ABB PVS800-IS, Руководство по оборудованию, Страница: 51 / 68

Поделиться
Скачать
ABB PVS800-IS Скачать руководство пользователя страница 51

Checking and repairing unpainted, zinc coated surfaces

￭

Materials

•

Sandpaper

•

Cleaning towels and liquids

•

Zinc coating on non painted surfaces: Würth Zinc 300 0892 200 with brush or Zinc Spray
Perfect 0893 114 113 (or similar)

Note:

Obey the instructions given by the material manufacturers.

￭

Procedure

WARNING!

Follow the steps given in section

Safe installation, start-up and

maintenance (page 10)

. Ignoring the instructions can cause physical injury or

death, or damage to the equipment.

Pay special attention to doors and lower parts of the walls which are potentially prone to
corrosion due to dust and humidity.

1.

If there is rust, remove the rust gently with sandpaper.

2.

Clean the damaged area and the area adjacent to it.

3.

Coat the damaged area with zinc coat. Würth Zinc 300 is preferred because it gives a
thicker coat. On larger areas Würth Zinc Spray Perfect can be used to speed up the
work and to provide a smoother surface appearance.

Maintenance   51

Checking and repairing unpainted, zinc coated surfaces

Materials

•

Sandpaper

•

Cleaning towels and liquids 

•

Zinc coating on non painted surfaces: Würth Zinc 300 0892 200 with brush or Zinc 
Spray Perfect 0893 114 113 (or similar)

Note!

 Obey the instructions given by the material manufacturers.

Procedure

WARNING! 

Follow the steps given in section 

Safe installation, start-up and 

maintenance

 on page 

10

. Ignoring the instructions can cause physical injury or 

death, or damage to the equipment.

Pay special attention to doors and lower parts of the walls which are potentially prone to 
corrosion due to dust and humidity. 

1. If there is rust, remove the rust gently with sandpaper.

2. Clean the damaged area and the area adjacent to it.

3. Coat the damaged area with zinc coat. Würth Zinc 300 is preferred because it gives a 

thicker coat. On larger areas Würth Zinc Spray Perfect can be used to speed up the 
work and to provide a smoother surface appearance.

Maintenance 51

Содержание PVS800-IS





































































Отзывы:

Нет отзывов