ABB ETP Скачать руководство пользователя страница 22

If the media is corrosive consider choosing the right diaphragm material.  If
there is any uncertainty please contact us for advice.
If existing diaphragm types are not sufficient it is possible to deliver transmitt-
ers with diaphragm coatings, for example teflon, epoxy, rubber. Please
contact us for information.
Even though a diaphragm material is sufficient for a corrosive media it will be
slightly affected. This means that the measurement will be slightly changed
over time (especially the zero point). This can be corrected by performing a
maintenance calibration or a recalibration.

The transmitters electronic- and electric connection housing is approved for
IP67. Use round signal/supply cable and tighten the cable feed through firmly.
Make sure that the electronic housing cover is tight.

If the transmitter is installed in a dirty environment, make sure that the
reference slit (see figure 1) always is open for the atmospheric pressure.

In plants with high vibration levels it is important to secure that the transmitt-
ers performance is sufficient. The most certain is to measure the vibrations
amplitude resp. acceleration.

The transmitters are designed and tested for:
3-25 Hz, amplitude 1,6 mm
25-60 Hz, amplitude 0,21 mm
60-100 Hz, accel. 19,6 m/s2
(Standards: IEC770 and DNV Certification note 2.4 location class B.)
If vibration levels exceeds this consider using the special transmitter type  N
(contact us for information).

Transmitter removable during operation. (connection 6)

There are certain considerations that must be considered for this transmitter
type. The diaphragm is more exposed on this type because the transmitter is
pushed in/out of the valve.
Make sure that the valve is not plugged or closed when the transmitter is
pushed in. If so the sensor might be permanently damaged.
This transmitter type has a small diaphragm and it is sensitive to damage or
corroded diaphragms. A maintenance calibration or recalibration might be
required periodically.

Om mediet är korrosivt tänk på att välja rätt membran.  Om det råder osäker-
het vid val av membran kontakta oss för rådgivning.
Om de befintliga membrantyperna inte räcker till kan vi leverera givare med
olika beläggningar på membranen, tex. teflon, epoxi mm. Kontakta oss för
information.
Även om ett membran fungerar bra mot ett korrosivt media kommer det ändå
att korrodera till en viss del. Detta innebär på sikt att givarens mätning
kommer att förskjutas (framför allt påverkas nollpunkten). Detta kan kompen-
seras med en underhållskalibrering eller omkalibrering.

Givarnas elektronik- och kopplingsutrymmen är klassade för IP67. Se dock
alltid till att använda rundmantlad kabel och att dra åt kabelgenomföringen
ordentligt.

Om givarna är monterade i en smutsig miljö, se till så att referensspalten mot
atmosfärs-trycket (se bild 1) inte blir igensatt.

I anläggningar med mycket vibrationer eller som vibrerar kraftig periodvis bör
det undersökas om givarens prestanda räcker till. Det bästa är att mäta
vibrationernas amplitud resp. acceleration.

Givarna är dimensionerade och testade för:
3-25 Hz, amplitud 1,6 mm
25-60 Hz, amplitud 0,21 mm
60-100 Hz, accel. 19,6 m/s2
(Normer: IEC770 och DNV Certification note 2.4 location class B.)
Om vibrationerna överstiger dessa värden kan problemet eventuellt lösas med
en speciell givartyp, anslutning N (kontakta oss för information).

Bytbar givare (anslutning 6)

För denna typ av givare finns vissa speciella hänsynstaganden som måste
göras. Eftersom givaren skjuts in/ut är dess membran extra utsatt.
Tänk på att ventilen inte får vara igensatt eller stängd när givaren ska skjutas
in. Sensorn kan då i värsta fall utsättas för övertryck och sprängas.
Denna givartyp har relativt små membran varför deformerade eller korroderade
membran lätt förändrar givarens mätning. En underhållskalibrering/om-
kalibrering kan behöva göras regelbundet.

22

Содержание ETP

































Отзывы: