manualshive.com logo in svg

ABB DCS800, Руководство по установке

Поделиться
Скачать
ABB DCS800 Скачать руководство пользователя страница 58

58 

 

   Stripped part covered with 

copper foil 

Stripped cable 

Conductive surface of the 

screen exposed 

 

 

 

 

Cable screen 
 

 

−

 

Cut the screen at the midpoint of the bare part. Be careful not to cut 
the conductors. 

−

 

Turn the screen inside out to expose its conductive surface. 

−

 

Cover the turned screen and the stripped cable with copper foil to 
keep the shielding continuous. 

Note: 

The ground wire (if present) must not be cut. 

−

 

Push the two parts of the lead-through plate together so that the 
conductive cushions press tightly round the foil covered screen. 

5.

 

Lock the two parts of the lead-through plate by tightening the positioning 
screws. 

6.

 

Top entry: If more than one cable go through a single grommet, the grommet 
must be sealed by Loctite 5221 (catalogue number 25551). 

 

 

 

Side 

view 

   

 

 

 

 

Top entry 
 
 

 
 
Electrical Installation 

3ADW000352R0101 DCS800-A Installation Manual e a

 

Содержание DCS800







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды