manualshive.com logo in svg

ABB DCS800, Руководство по установке

Поделиться
Скачать
ABB DCS800 Скачать руководство пользователя страница 57

57

 

View from below

 

 

 
 
Thinnest cable 
 
 
 
 
 
 
 
 
 
 
 
 
Thickest cable 
 

 

 
 

Lead-through plate 
 

Bottom and Top Entry 

 Proceed 

as 

follows: 

 
1)

 

Loosen the lead-through plate position screws. Pull the two parts apart. 

2)

 

Bottom entry 
Lead the cable inside the cabinet through the conductive cushions. 
Top entry 
Lead the cable inside the cabinet through the grommet and the conductive 
cushions. If you have several cables, bunch them together at the grommet, but 
ensure that each cable has a proper contact to the cushions on both sides. 

3)

 

Strip off the cable plastic sheath above the base plate (just enough to ensure 
proper connection of the bare screen and the conductive cushions). 

4)

 

Earth the screen by means of the conductive cushions: 

 

a.

 

If the outer surface of the screen is conductive: 

−

 

Push the two parts of the lead-through plate together so that the 
conductive cushions presses tightly around the bare screen. 

b.

 

If the outer surface of the screen is covered with non-conductive material: 

 

 

 
 

 Electrical Installation

 

3ADW000352R0101 DCS800-A Installation Manual e a

 

Содержание DCS800







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды