ABB AV1 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 126

background image

QUICK START

TYPE AV1 POSITIONER WIRING

B - 10

4.

Grounding positioners should be done in accordance with local

electrical codes (in U.S, National Electrical Code, ANSI/NFPA 70. In
Canada, Canadian Electrical Code, CSA c22.1). A grounding screw is
provided inside the AV enclosure for grounding, denoted by .

NOTES:

1.

The grounding screw located inside the AV enclosure is a

safety ground and should not be used to ground the shielded pair.

2.

The positioner must be grounded to avoid ground loop

conditions.

TYPE AV1 POSITIONER WIRING

This section applies to the following positioners:

•

Type AV1___1__.

•

Type AV1___2__.

NOTES:

1.

For a Type AV1___0__ positioner, no electrical wiring is

required.

2.

If using a twisted shielded pair for signal wiring, ground one end

of the shielded pair at the source. Trim the other end of the pair,
located inside the enclosure, so that bare wires are not exposed.

1.

If equipped with optional 4 to 20-mA position transmitter (Type

AV1___2__), connect a 24-VDC power supply in series with the
required output load (Table

) to terminals TB1-1 (+) and TB1-2 (-)

(Fig.

). Refer to

for detailed information about posi-

tion transmitters.

2.

If equipped with optional potentiometric position transmitter (Type

AV1___2__), connect a power supply (maximum 35 VDC or 30 VAC)
across TB1-1 and TB1-3. Use the signal across TB1-1 and TB1-2 or
TB1-2 and TB1-3 for position transmitter feedback. Refer to

for detailed information about position transmitters.

NOTE:

Route the wiring inside the positioner so it does not become

entangled with moving parts. A cable clamp (Fig.

inside the positioner so entanglement can be avoided.

3.

Grounding positioners should be done in accordance with local

electrical codes (in U.S, National Electrical Code, ANSI/NFPA 70. In
Canada, Canadian Electrical Code, CSA c22.1). A grounding screw is
provided inside the AV enclosure for grounding, denoted by .

NOTES:

1.

The grounding screw located inside the AV enclosure is a

safety ground and should not be used to ground the shielded pair.

2.

The positioner must be grounded to avoid ground loop

conditions.

«
...
104
105
106
107
108
...
»

Содержание AV1































































































































Отзывы:

Нет отзывов

Похожие инструкции для AV1

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: 3B6 Страницы: 30

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Kathrein Страницы: 10

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Wagner Meters Страницы: 17

Бренд: Yamaha Страницы: 98

Бренд: P3 International Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды