manualshive.com logo in svg

ABB AquaProbe 2, Руководство по установке

Поделиться
Скачать
ABB AquaProbe 2 Скачать руководство пользователя страница 5

Insertion-Type Electromagnetic Probe Flowmeter

AquaProbe 2

1 Introduction

IM/AP

 Issue 9

3

1 Introduction

The AquaProbe electromagnetic insertion flowmeter is designed for measurement of the velocity of water.

The flowmeter, available in four standard lengths, can be installed in any pipeline of internal diameter from
200mm (8in) to 8000mm (360in), through a small tapping.

The AquaProbe is designed for use in survey applications such as leakage monitoring and network analysis
and in permanent locations where cost or space limitations preclude the use of conventional closed pipe
meters.

1.1 System Schematic

Note.

The tip of the AquaProbe is a precision-built part of the equipment and must be handled with care.

When the AquaProbe is not in use, fully retract the tip of the probe and replace the end-cap.

When removing/inserting the probe into the pipeline, ensure that the valve is fully open.

Damage to the probe effects the performance.

Physical damage to the probe invalidates the warranty. 

Fig. 1.1 System Schematic

Power

Output

Sensor

Potted

Connections

AquaMaster

Содержание AquaProbe 2













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды