manualshive.com logo in svg

ABB ACSM1 Series, Руководство по оборудованию

Поделиться
Скачать
ABB ACSM1 Series Скачать руководство пользователя страница 25

Planning the cabinet assembly

25

Planning the cabinet assembly

What this chapter contains

This chapter guides in planning the installation of a drive module into a user-defined 
cabinet. The issues discussed are essential for safe and trouble-free use of the drive 
system.

Note: 

The installation examples in this manual are provided only to help the installer 

in designing the installation. 

Please note that the installation must, however, 

always be designed and made according to applicable local laws and 
regulations.

 ABB does not assume any liability whatsoever for any installation 

which breaches the local laws and/or other regulations.

Cabinet construction

The cabinet frame must be sturdy enough to carry the weight of the drive 
components, control circuitry and other equipment installed in it.

The cabinet must protect the drive module against contact and meet the 
requirements for dust and humidity (see the chapter 

Technical data

).

Disposition of the devices

For easy installation and maintenance, a spacious layout is recommended. Sufficient 
cooling air flow, obligatory clearances, cables and cable support structures all 
require space.

For layout examples, see section 

Cooling and degrees of protection

 below.

Grounding of mounting structures

Make sure all cross-members or shelves on which drive system components are 
mounted are properly grounded and the connecting surfaces left unpainted.

Note:

 Ensure that the components are properly grounded through their fastening 

points to the installation base.

Note:

 It is recommended that the mains filter (if present) and the drive module be 

mounted on the same mounting plate.

Содержание ACSM1 Series

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды