ABB ACS 800 Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 162

background image

Mechanical installation of non-pre-assembled units (ACS800-04M)

81

Fastening the drive module by top to the cabinet frame

In addition to the base fastening, it is recommended to fasten the module to the
cabinet also from the fastening points at the top. Refer to

Dimensional drawings

the vertical fastening points.

If the module is not fastened from the back top to the cabinet frame, it must be
fastened from the front top fastening points during transportation or in case of
vibration.

Fastening the drive module to wall (wall-mounted units only, not for base-mounted
units)

Requirements for protection

The drive module must be protected against contact, dust and humidity (see chapter

Technical data

in

ACS800-04/04M/U4 Hardware Manual

[64671006 (English)].

Requirements for the wall

The wall must be as close to vertical as possible, of non-flammable material and
strong enough to carry the weight of the unit. Check that there is nothing on the wall
to inhibit the installation.

Floor

The floor/material below the installation must be non-flammable.

«
...
79
80
81
82
83
...
»

Содержание ACS 800 Series



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACS 800 Series

Бренд: ABB Страницы: 6

Бренд: IBC Страницы: 4

Бренд: Western Global Страницы: 21

Бренд: YASKAWA Страницы: 47

Бренд: Mecc Alte spa Страницы: 34

UBA Pro RT Series

Бренд: JCM GLOBAL Страницы: 196

$R.V.R. Elettronica TCP/IP-INT-TEX User Manual preview$

Бренд: R.V.R. Elettronica Страницы: 26

Бренд: VALSTEAM ADCA Страницы: 5

Бренд: EC POWER Страницы: 50

TERMALINE 8251 Series

Бренд: BIRD Страницы: 24

Бренд: C-COM Satellite Systems Страницы: 68

Бренд: SCHUNK Страницы: 40

Hinds-Bock SP-64B

Бренд: Middleby Страницы: 15

Бренд: dimos Страницы: 20

Бренд: erowa Страницы: 23

Бренд: Parker Страницы: 56

Бренд: OEZ Страницы: 8

ICE MASTER IMT1000

Бренд: CAMION Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды