ABB ACS 800 Series Скачать руководство пользователя страница 40

Страница: 40 / 162

Mechanical installation of pre-assembled units (ACS800-04/U4)

Move the transport package by pallet truck to the installation site. Unpack the
package as shown below.

Delivery check

Check that there are no signs of damage. Before attempting installation and
operation, check the information on the type designation label of the drive to verify
that the unit is of the correct type.

Undo the
fastening

screws.

The following items are fastened to
the drive module:
• pedestal
• output busbars U2, V2 and W2
• busbars for brake resistor

connection if brake chopper is
included.

• DC busbars if ordered

The following items are located below the drive
module:

Drive Control Unit (RDCU)

Note:

Optional modules (if ordered) are

factory installed onto the RMIO board in
the RDCU unit.

The fibre optic cables and

power supply cable to be connected to the
RMIO board are coiled on the top of the
drive module.

Base and wall fastening brackets,
terminals for output cable connection
and PE grounding. Screws are included
in a plastic bag.

Manuals (hardware, appropriate firmware,
optional module), delivery documents,
residual voltage warning stickers

Control panel with a 3 m (98 in.) cable
and RPMP control panel mounting kit (if
ordered)

Содержание ACS 800 Series



































































































































































Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды

ABB ACS 800 Series, Инструкция по установке и эксплуатации шкафа

Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды