ABB ACS 800 Series Скачать руководство пользователя страница 22

Страница: 22 / 162

The ACS800-04/U4 and ACS800-04M

Printed circuit boards

The drive contains the following printed circuit boards as standard:

• main circuit board (AINT)

• motor control and I/O board (RMIO) with a fibre optic link to the AINT board

• input bridge control board (AINP)

• input bridge protection board (AIBP) which includes snubbers for the thyristors

and varistors

• power supply board (APOW)

• gate driver control board (AGDR)

• diagnostics and panel interface board (ADPI)

• brake chopper control board (ABRC) with D150

Motor control

The motor control is based on the Direct Torque Control (DTC) method. Two phase
currents and DC link voltage are measured and used for the control. The third phase
current is measured for earth fault protection.

Содержание ACS 800 Series



































































































































































Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды

ABB ACS 800 Series, Инструкция по установке и эксплуатации шкафа

Результаты поиска

Содержание ACS 800 Series

Отзывы:

Похожие инструкции для ACS 800 Series

Бренды по названию

Популярные бренды