ABB ACH 400 Скачать руководство пользователя страница 31

Страница: 31 / 44

Chapter 4 – Programming

ACS/ACH 400 Direct N2 Bus Interface

4-9

Fault Queue

The ACS/ACH 400 has a fault queue which
records the latest three faults. This queue can
be read using the Analog Input points 13 - 15.

Faults

Faults are abnormal situations detected by the
drive, which cause the drive to fault. The fault
information is both displayed on the drive panel
and is placed into the fault queue.

To get a more detailed description of the
corresponding faults see the appropriate ACS/
ACH 400 drive User’s Manual.

Table 4-2 “Drive Faults” lists the fault code
numbers which correspond to the faults in the
fault queue parameters.

Table 4-2 Drive Faults

Code

Message

Description

FL 1

OVERCURRENT

Overcurrent:
• Possible mechanical problem.
• Acceleration and/or deceleration times may be too

short.

• Power supply disturbances.

FL 2

DC
OVERVOLTAGE

DC overvoltage:
• Input voltage too high.
• Deceleration time may be too short.

FL 3

ACS400 or
ACH400
OVERTEMP

ACS/ACH 400 overtemperature:
• Ambient temperature too high.
• Severe overload.

FL 4
*

SHORT CIRCUIT

Fault current:
• Short circuit.
• Power supply disturbances.

FL 5

OUTPUT
OVERLOAD

Output overload.

FL 6

DC
UNDERVOLTAGE

DC undervoltage.

FL 7

ANALOG INPUT 1

Analog input 1 fault. Analog input 1 value is less than

MINIMUM

AI1 (1301). See also parameter 3001

MIN

FUNCTION

FL 8

ANALOG INPUT 2

Analog input 2 fault. Analog input 2 value is less than

MINIMUM

AI2 (1304). See also parameter 3001

MIN

FUNCTION

FL 9 MOTOR

OVERTEMP

Motor overtemperature. See parameters 3004-3008.

Содержание ACH 400













































Результаты поиска

Содержание ACH 400

Отзывы:

Похожие инструкции для ACH 400

Бренды по названию

Популярные бренды

ABB ACH 400, Руководство пользователя

Результаты поиска

Содержание ACH 400

Отзывы:

Похожие инструкции для ACH 400

Бренды по названию

Популярные бренды