manualshive.com logo in svg

ABB ACH 400, Руководство пользователя

Поделиться
Скачать
ABB ACH 400 Скачать руководство пользователя страница 25

Chapter 4 – Programming

ACS/ACH 400 Direct N2 Bus Interface

4-3

Binary Output

The binary output points support the following 
features:

•

Binary Output value

•

Override value is used to change the 
Binary Output value. It is not possible to 
return to the previous value by removing 
the override. The override feature is 
used only to change the value.

Communication 
Setup

To activate the direct N2 Bus connection, set 
parameter 5005 PROTOCOL SEL to OEM 
APPLIC (4). If you can not see this selection on 
the panel, your drive does not have N2 protocol 
software in the application memory.

For the direct N2 Bus communication there are 
new setup parameters on the drive. These are 
located in the group 53 OEM APPLICATION. 
These parameters are shown in Table 4-1 
“Group 53 OEM APPLICATION”. 

Table 4-1 Group 53 OEM APPLICATION

Parameter

Panel Text

Range/

Unit

Description

1 OEM Applica-

tion ID and 
Revision

5301 OEM 
APP PAR1

1010 - 

1099

N2 Software ID and 
revision

2 Drive ID-num-
ber

5302 OEM 
APP PAR2

1 - 255

Drive N2 address

3 Communication 

time-out time

5303 OEM 
APP PAR3

1 – 600

(1.0 - 

60.0 s)

Time limit for 
communication loss
detection

4 Communication 
fault function

5304 OEM 
APP PAR4

0 – 3

Operation in case 
communication with 
master device is lost

5 Good Message 
Counter

5305 OEM 
APP PAR5

0 – 

65535

Rolling counter for 
good messages

6 Bad Message 
Counter

5306 OEM 
APP PAR6

0 – 

65535

Communication error 
counter

Содержание ACH 400













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды