ABB ACH 400 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

Chapter 4 – Programming

4-4

ACS/ACH 400 Direct N2 Bus Interface

1 OEM Application ID and
Revision

This parameter shows the application software
ID and revision code. First two digits are the ID
and next two are the revision code. The
Application ID for N2 software is 10.

2 Drive ID-number

This parameter selects the node number for the
ACS/ACH 400 drive on the N2 Bus. Default
value is 0, which disables the communication.

3 Communication time-out
time

This parameter is used to define the time-out
value for the communication loss function. If the
Metasys system does not communicate with
the drive for this period of time, a
communication loss fault is generated.

4 Communication Fault
Function

This parameter selects what is being done
when there is a communication loss from the
Metasys system down to the drive. The
communication loss is defined so that if there
are no messages to the drive within a time
period defined in the parameter 8
TIME-OUT SELECT, a communication loss is
generated.

The possible selections are:

0 = NOT SELECTED
Ignore
The communication loss is ignored.

1 = FAULT
Stop the Drive
The drive will show the

OEM

fault on the panel

and will stop. The drive will also go to the Off-
Line state on the N2 Bus. To restart the drive,
communication must be restored and the fault
must be cleared.

7 Framing Error
Counter

5307 OEM
APP PAR7

0 –

65535

Number of detected
framing errors

8 Overrun
Counter

5308 OEM
APP PAR8

0 –

65535

Number of detected
overrun errors

9 Protocol Soft-
ware Error

5309 OEM
APP PAR9

0 – 3

Protocol software
error code

Parameter

Panel Text

Range/

Unit

Description

«
...
24
25
26
27
28
...
»

Содержание ACH 400













































Отзывы:

Нет отзывов

Похожие инструкции для ACH 400

Бренд: FrSky Страницы: 2

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Hanna Instruments Страницы: 88

Black Force Wireless

Бренд: Hama Страницы: 10

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 50

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 22

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 9

FIeldPoint FP-AO-200

Бренд: National Instruments Страницы: 13

Бренд: National Instruments Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды